HOT INFORMATION
<
  • Proper use of the spring
    Proper use of the spring
    2018 . 09 . 30
    315
    Daisy
    Please avoid the improper way of using (1) more than the use of the maximum compression (300000 back to the conditions, after a close with the use of a long) stress causing the wreck, close to close with the use of a long, can make the spring line department gradually close to that, because of the high spring constant change caused by load curve with high, nearly and produce high stress to make spring break, please do not use more than 300000 times.The use of the spring without prepressure due to the gap caused the spring up and down vibration caused the spring distortion, if there is prepressure, the spring is relatively stable.When the spring is used, the pin and the spring will be worn and broken.When used without spring guide, the bottom of the spring and the body of the spring are eas...
    more
  • Metal spring plays an important role in safety valve
    Metal spring plays an important role in safety valve
    2018 . 09 . 29
    393
    Daisy
    The spring relief valve is mainly composed of spool, seat, stem, spring and adjusting screw.The relief valve mainly USES spring force to press the spool on the seat.When the boiler pressure exceeds the pressure exerted by the spring on the upper part of the spool, the spool and stem are lifted and steam is discharged.When the boiler pressure is lower than the spring pressure acting on the upper part of the spool, the spool falls on the seat and the boiler stops discharging steam.The spool is a cone with a slight protrusion around the edge of the spool.When the steam opens the valve core, the edge of the valve core is also affected by steam pressure, which makes the whole area of action increase suddenly, and the valve opens when the valve stops.When the drop force is reduced, the steam for...
    more
  • Analysis of spring corrosion
    Analysis of spring corrosion
    2018 . 09 . 29
    337
    Daisy
    The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which is a chemical corrosion.If the spring is in contact with the electrolyte solution, the corrosion caused by the action of the micro battery is called electrochemical corrosion.For example, the spring is...
    more
  • Development of special spring and material requirements
    Development of special spring and material requirements
    2018 . 09 . 28
    215
    Daisy
    The special-shaped spring contains spring clip, tension spring and torsion spring, and the generalized special-shaped spring also includes snake spring, corrugated spring, bar spring and other complicated springs.Special-shaped spring is the basic part with wide application range and multifarious variety in automobile, motorcycle, electric appliance and instrument products. Its quality and life directly affect the performance of main engine products.Hyundai has made it a key component.Over 90% of special-shaped springs at home and abroad are made of two kinds of materials: lead quenched carbon steel or cold hardened austenite stainless steel. They do not need quenching, but need low temperature tempering after winding, which can not only eliminate the residual stress in the process of cold...
    more
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
118
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 08 - 06
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
119
Inspection content and specification for spring parts(part 5)
Inspection content and specification for spring parts(part 5)
2018 - 08 - 17
Detection of the characteristics of 7.2 torsion springsWhen measuring torque, the size of the torsional spring axis must be suitable. The inner diameter of the spring should be kept to a certain gap, and the friction force and friction torque caused by the contraction of the inner diameter of the spring should be avoided, and the measurement accuracy should be affected. But the spindle can not be too small, otherwise it will cause the offset between the external torque and the measuring torque center, resulting in the error of the torque measurement. The specific testing program for torsion sp...
120
Causes and preventive measures of quenching cracks
Causes and preventive measures of quenching cracks
2018 - 08 - 31
1. Shape effect is mainly caused by design factors, such as small fillet R, inappropriate location of acupoints, poor cross-sectional transition. 2. Overheating (overheating) is mainly caused by improper temperature control or running temperature, excessive process setting temperature, uneven furnace temperature and other factors. Preventive measures include overhaul, calibration of temperature control system, correction of process temperature, the addition of pad iron between the workpiece and furnace floor, etc.3. Decarbonization is mainly caused by overheating (or overburning), unprote...
121
Method for improving heat treatment performance
Method for improving heat treatment performance
2018 - 09 - 14
Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat ...
122
Working characteristics of pressure spring
Working characteristics of pressure spring
2018 - 09 - 26
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle ...
123
Method for improving heat treatment performance
Method for improving heat treatment performance
2018 - 10 - 11
Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat ...
124
Penetration testing of springs
Penetration testing of springs
2018 - 10 - 22
Osmosis detection will be the basic principle of the spring of dip coating (penetrant) some penetration ability of the solution, the infiltration of surface defects, and then to remove excess penetrant, appeared in the surface layer of the tu yi agent again, at this point defects remaining in the penetrant sucked out, under the purple pay-off (fluorescence) observation or direct observation, can be found that the existence of defects.Osmotic detection can be used for the detection of ferromagnetic springs as well as non-ferromagnetic materials such as copper alloy and austenitic stainless stee...
125
The working characteristic of tension spring
The working characteristic of tension spring
2018 - 12 - 03
Today, the development of science and technology, spring has been a very important hardware accessories in our life, different products use the spring is not the same, the longest used spring can be roughly divided into: tension spring, torsion spring, compression spring, spiral spring, flat spring.The following is a very practical tension spring characteristics of the application:Many different products or hooks are used to ensure that the tension spring tension source, tension spring and compression spring work in the opposite way, tension spring is in the extension or pull out of the revers...
126
Which industry is the main application of spring?
Which industry is the main application of spring?
2018 - 07 - 25
1, matching springs and springs based on automobiles, motorcycles, diesel engines and gasoline engines. This type of spring has valve spring, suspension spring, damping spring and clutch spring, etc., with a large amount, which accounts for about 50% of the spring production. At the same time, the technical level is also high, it can be said that the technical level of these springs is representative, they are mainly to the high fatigue life and high anti relaxation direction, thus reducing the quality. 2. Large springs and plate springs, which mainly include railway rolling stock, heavy ...
NEW INFORMATION / More
118
Summary of spring parameters and symbols (Part I)
Summary of spring parameters and symbols (Part I)
2018 - 08 - 01
Core tips: elastic formula: F=kx, F for elastic, K for the stiffness coefficient, X for the length of the spring length, such as the length of the spring for example, to test a spring of 5N: 5N pull the stiffness coefficient of 100N/m spring, the spring is elongated 5cmF= KX, K is the stiffness coefficient (unit is Newton per meter), X is the spring elongation (unit is rice), this law is called Hooke's law.Elastic formula:F=kx, F is elastic, K is stiffness coefficient, X is spring stretch length.For example, to test a 5N spring:When a spring with a stiffness coefficient of 100N/m is pulled...
119
The development course of spring material (Part 3)
The development course of spring material (Part 3)
2018 - 08 - 14
(5) the development of spring steel wireAfter more than 100 years of development, the technology of spring steel has experienced lead hardened to oil quenching, and now it develops to induction hardening. Coupled with the continuous innovation and improvement of technology and equipment, the quality of varieties is constantly updated. The newly developed valves have been developed by induction heating and tempering with spring steel wire. It has been proved that the plastic, toughness, relaxation, fracture toughness, delayed fracture resistance, fatigue life and so on are all compared with oil...
120
Production of spring
Production of spring
2018 - 08 - 28
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
121
Vibration damping spring is a commonly used elastic element
Vibration damping spring is a commonly used elastic element
2018 - 09 - 11
Vibration damping spring is a common elastic component, which is widely used in various vibration equipment and automobile manufacturing industries. It has the advantages of good stability, low noise, good isolation effect and long service life.Compression springs, rubber springs, composite springs, air bag springs are vibration - reducing springs.Vibration damping spring can be divided into: wire compression spring, rubber spring, compound spring, rubber air spring, etc.Steel wire compression spring is a spiral spring under pressure, it USES the material section is mostly circular, also USES ...
122
The difference between three common springs
The difference between three common springs
2018 - 09 - 22
Spring is a kind of elastic element widely used in the mechanical and electronic industries. Spring can produce greater elastic deformation when loaded, and convert mechanical work or kinetic energy into deformation energy. After unloading, the deformation of spring disappears and returns to its original state, and the deformation energy is transformed into mechanical work or kinetic energy.The ratio of load and deformation of the spring is called spring stiffness.  There are many kinds of springs. They are used in various fields. According to the deformation condition, they can be divide...
123
The Standing treatment of the spring
The Standing treatment of the spring
2018 - 10 - 09
1. The standing treatment of the compression spring is to compress the spring to the working limit height or to tighten the height several times, usually 3 to 5 times;For the stretching spring, the length of the spring is drawn to the working limit several times;Torsion spring, is the spring in the working direction of the 5522 for the ultimate torsion Angle several times.2. Strong pressure (strong tension and strong torsion) treatment for compression spring is to press the spring into the material layer and the stress exceeds the yield point, resulting in negative residual stress on the surfa...
124
Spring-shot technology requirements
Spring-shot technology requirements
2018 - 10 - 19
1、 preparation before peening1) the size and surface roughness before spring-shot blasting should meet the requirements of the pattern, except for special instructions (if it is necessary to reprocess the shot blasting surface).2) the spring shall complete the prescribed heat treatment before shot peening.3) the non-destructive test of the spring shall be completed before the shot peening treatment, or after the shot peening if there is special requirement.4) the surface of the spring to be sprayed should be clean, dry and free of oil.2、 treatment after shot peening1) the heating temperature o...
125
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 11 - 01
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
126
Constant Force Spring
Constant Force Spring
2020 - 01 - 13
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant.   Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound in...
CONTACT US / More
Consultation
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
Constant Force Spring
Constant Force Spring
2020 . 01 . 13
点击次数: 177
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
More
Compression Springs
Compression Springs
2020 . 01 . 13
点击次数: 178
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
More
Spring wire materials
Spring wire materials
2020 . 01 . 06
点击次数: 133
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
More
How much do you know about the cleaning of stainless steel springs？
How much do you know about the cleaning of stainless steel springs？
作者： nelson
发布时间： 2018 / 08 / 10
点击次数： 130
Stainless steel spring general precautions when washing, please pay attention to no surface friction to avoid the use of bleaching components and washing liquid containing abrasives, steel ball, grinding tools, etc., in order to remove the washing liquid, washing the end, rinse the surface with clean water.Surface state and washing methodDust and scaling - wash with soap or warm water.Label and film - scrub with warm water and weak detergent.Binder ingredients - use alcohol or organic solution;Fat, oil, lubricating oil contamination - with soft cloth or paper after drying with a neutral detergent or ammonia solution or special detergent to wash;Bleaching agent and seed acid adherence - wash with water immediately, soak with ammonia or neutral soda solution, then wash with neutral detergent...
>>
Common specifications of spring
Common specifications of spring
作者： nelson
发布时间： 2018 / 08 / 09
点击次数： 64
The number of diameter length is described!(1) the diameter of the spring wire d: is the wire diameter of the spring. (2) the maximum outer diameter of the spring outer diameter D: spring. (3) the inner diameter of the spring D1: the smallest outer diameter of the spring.(4) the middle diameter of the spring D2: the average diameter of the spring. Their formula is: D2 = (D + D) = 2 = D 1 + D = D D.(5) apart from the support ring, the distance between the two adjacent circles of the spring corresponding to the axial distance of the point on the middle diameter is t:, and is expressed by t. (6) the number of effective circles n: springs can keep the number of circles with the same pitch.(7) Number of supporting coils n2: In order to make the spring work uniformly, ensure that ...
>>
A brief history of the development of Hooke
A brief history of the development of Hooke's law
作者： nelson
发布时间： 2018 / 08 / 09
点击次数： 74
At first, during the experiment, Hooke found that the weight added to the spring was proportional to the elongation of the spring, and he tested his conjectures by many experiments. In 1678, Hooke wrote a spring paper, which introduced the results of experiments on elastic objects, laying the foundation for the development of material mechanics and elastic mechanics.Spring dynamometerIn the early nineteenth Century, under the premise of a lot of experimental work in the former, British scientist Thomas Yang summed up the research results of Hooke and others, pointing out that if the elongation of the elastomer exceeds a certain limit, the material will break, and the law of elastic force is no longer applicable, and clearly points out the scope of application of the law of elastic force. (...
>>
Manufacturing of Springs
Manufacturing of Springs
作者： nelson
发布时间： 2018 / 08 / 08
点击次数： 61
Springs can also be classified by how they’re made. The first spring that comes to most people’s minds is probably a metal coil spring, also known as a helical spring. However, there are many other types. Even an elastic band can be considered a variable rate spring, since it stores mechanical energy. Coil SpringsLightweight coil springs are made by forming metal wires on an CNC coiling machine. The multi-axis CNC control allows you to create variable pitches and end conditions only limited by your imagination. Springs that come off the coiling machines do not have springy properties. They need to be heated to a high temperature (typically 500 degrees Fahrenheit or more) to relieve stress, then quenched to create shape memory.In contrast, when making heavy duty coil springs, the wire is he...
>>
Material and characteristics of spring
Material and characteristics of spring
作者： nelson
发布时间： 2018 / 08 / 08
点击次数： 89
The spring is often subjected to variable load or impact load. In order to ensure that the spring can work permanently and reliably, the material must have high elastic limit and fatigue limit. At the same time, it should have enough toughness and plasticity and good heat treatment.Spring materials and properties can be consulted in relevant manuals, specifications and standards (GB/T129.6-92, GB4357-89). The common spring steel is mainly:1: carbon spring steelThis kind of spring (such as 65, 70 steel, etc.) has the advantages of cheap price, convenient source of raw materials, low elastic limit, easy to lose elasticity after repeated deformation, and can not work at 130 degrees.2: low manganese spring steelCompared with carbon spring steel, the spring steel, such as 65Mn, has the advantag...
>>
What is the fall of autumn?
What is the fall of autumn?
作者： nelson
发布时间： 2018 / 08 / 07
点击次数： 56
What is the fall of autumn?The fall of autumn, the thirteenth throttle of the twenty-four solar calendar in the lunar calendar, is the first throttle of autumn, marking the official start of the season of Meng Qiu: "autumn" means the summer to cool. By the beginning of autumn, the Chinese parasol trees began to shed their leaves. From the point of view of writing, the word "Qiu" is composed of grass and fire characters. Autumn is a transitional season from hot to cool and then from cold to cold.The fall of autumn, July. A word can be found in spring. Autumn is the same.At the beginning, cool wind. The wind of the west is cool and cool. Temperature changes and cool air begins to eliminate. "Zhou language" said the fire to see and the wind and cold is also.Two w...
>>
Each of these types can be further characterized.
Each of these types can be further characterized.
作者： nelson
发布时间： 2018 / 08 / 06
点击次数： 47
We can look at the relationship between the force applied to a spring and its resulting displacement. Again, there are three classes of springs: linear (or constant rate) springs, variable rate springs, and constant force springs. Linear springs Linear springs obey Hooke’s Law (F=k*x), which means that the force needed to extend or compress such a spring by distance x is proportional to the distance, as long as the force doesn’t exceed the elastic limit of the spring. Torsion springs obey an analogous version of Hooke’s Law (F=k*θ, where θ is an angle). In both cases, k is the spring rate, and it stays constant, no matter the spring’s deflection. This is why linear springs are also known as constant rate springs. Variable rate springsOn the other hand, a variable rate spring doesn’t have t...
>>
Types of Springs and their Applications
Types of Springs and their Applications
作者： nelson
发布时间： 2018 / 08 / 06
点击次数： 85
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sacrificed to satisfy my curiosity. These days, I appreciate the grown-up applications of springs, especially when I drive over potholes on Highway!
>>
The effect of the production process of the spring factory on the product
The effect of the production process of the spring factory on the product
作者： nelson
发布时间： 2018 / 08 / 03
点击次数： 64
Spring is no stranger to everyone. This element is seen everywhere in life. It is also one of the important parts of many industrial machinery equipment. There are many kinds, with different forms, specifications and sizes, and are widely used in the field. Now the spring plant is basically able to produce a variety of different springs. This component is made with special steel. The structure is relatively simple, but it is also required for the production process, so the manufacturer's production equipment and technology will affect the finished product.So if you need to choose a better brand or manufacturer to buy, because it is difficult to judge the quality of the quality of the product, it needs to be used to reflect, but to wait for the problem in the solution is more troublesom...
>>
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Site map
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat