HOT INFORMATION
<
  • 2018 . 10 . 15
    371
    Daisy
    (1) deformation heat treatment -- the combination of deformation reinforcement and heat treatment enhancement to further improve the strength and toughness of steel.Heat treatment of deformation has high, medium and low temperature.The high temperature deformation heat treatment is to produce the deformation immediately after the austenitic state at a stable distance, or can be combined with forging or hot rolling, that is, quenching immediately after hot forming.The deformation heat treatment has been applied to automobile plate spring production.(60 si2mn)(2) isothermal quenching of spring -- isothermal quenching can be adopted for springs with small diameter or sufficient permeability. It can not only reduce deformation, but also improve strength and toughness. It is better to conduct a...
  • 2018 . 10 . 12
    340
    Daisy
    There are many ways of making spring, but the main forming part is cold forming and hot forming.In spring in the cold forming process, the spring mainly made by oil material toughening, lead bath quenching tempering spring wire, cold drawn wire, etc., using this kind of material in the manufacturing process of spring generally do not need special heat treatment and only requires the stress relieving, adopted by the spring design work stress and material performance.Spring cold forming process is generally suitable for special-shaped spring with small line diameter or more complicated shape, such as line diameter less than 15mm, various kinds of snap, pull, twist spring, convex, concave and arc spring, etc.The cold forming process is simple and avoids the deformation and decarburization of ...
  • 2018 . 10 . 12
    266
    Daisy
    The spring is often corroded by the surrounding medium in the process of manufacture, storage and use.As the spring works under the influence of the spring force, the spring force will change and lose its function after being corroded.Therefore, preventing the corrosion of the spring can guarantee the stability of the spring and extend its service life.The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, causing corrosion of the spring is called chemical corrosion.For example, the spring is oxidized in the particu...
  • 2018 . 10 . 11
    381
    Daisy
    Type of paint used on spring surfacesThe oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then made of ferrous ironSodium sulfate interacts with sodium ferrite to form magnetic iron oxide (Pe3O4), or oxide film, with a thickness of about 0.5-1.5 microns.The co...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
91
2018 - 09 - 29
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
92
2018 - 10 - 16
The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension ...
93
2018 - 10 - 26
Please avoid the improper way of using (1) more than the use of the maximum compression (300000 back to the conditions, after a close with the use of a long) stress causing the wreck, close to close with the use of a long, can make the spring line department gradually close to that, because of the high spring constant change caused by load curve with high, nearly and produce high stress to make spring break, please do not use more than 300000 times.The use of the spring without prepressure due to the gap caused the spring up and down vibration caused the spring distortion, if there is prepress...
94
2019 - 12 - 30
Spring design and its fabrication play an important role in manufacturing and industry around the globe. Springs come in all shapes and sizes to meet industry needs and are made from a wide range of metal alloys. Materials used for spring design and wire forming consist of high strength alloys.In general, wire formed into springs is cold rolled or drawn, and a made of medium to high carbon steel with high yield strength that allows for excellent elastic properties.Mechanical PropertiesThe mechanical principles of springs are very basic. They are an elastic component. Potential mechanical ...
95
2018 - 04 - 18
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens. Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms. Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
96
2018 - 07 - 30
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30...
97
2018 - 08 - 10
Stainless steel spring general precautions when washing, please pay attention to no surface friction to avoid the use of bleaching components and washing liquid containing abrasives, steel ball, grinding tools, etc., in order to remove the washing liquid, washing the end, rinse the surface with clean water.Surface state and washing methodDust and scaling - wash with soap or warm water.Label and film - scrub with warm water and weak detergent.Binder ingredients - use alcohol or organic solution;Fat, oil, lubricating oil contamination - with soft cloth or paper after drying with a neutral deterg...
98
2018 - 08 - 24
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens.Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms.Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
99
2018 - 09 - 07
In the heat treatment of forgings, the way of placing parts to reduce deformation is to hang them vertically as far as possible, to place them vertically at the bottom of the furnace, to support them horizontally with two points, to place the fulcrum between one-third and one-fourth of the full length, and to place them flat on the heat-resistant steel tooling.In the cooling process of parts, the types, cooling properties and hardenability of quenching medium are related to deformation. The change of cooling performance can be adjusted by changing the viscosity, temperature, liquid pressure, a...
NEW INFORMATION / More
91
2018 - 08 - 09
The number of diameter length is described!(1) the diameter of the spring wire d: is the wire diameter of the spring. (2) the maximum outer diameter of the spring outer diameter D: spring. (3) the inner diameter of the spring D1: the smallest outer diameter of the spring.(4) the middle diameter of the spring D2: the average diameter of the spring. Their formula is: D2 = (D + D) = 2 = D 1 + D = D D.(5) apart from the support ring, the distance between the two adjacent circles of the spring corresponding to the axial distance of the point on the middle diameter is t:, and is expressed ...
92
2018 - 08 - 23
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kin...
93
2018 - 09 - 07
In the heat treatment of forgings, the way of placing parts to reduce deformation is to hang them vertically as far as possible, to place them vertically at the bottom of the furnace, to support them horizontally with two points, to place the fulcrum between one-third and one-fourth of the full length, and to place them flat on the heat-resistant steel tooling.In the cooling process of parts, the types, cooling properties and hardenability of quenching medium are related to deformation. The change of cooling performance can be adjusted by changing the viscosity, temperature, liquid pressure, a...
94
2018 - 09 - 19
Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually ...
95
2018 - 09 - 29
The spring relief valve is mainly composed of spool, seat, stem, spring and adjusting screw.The relief valve mainly USES spring force to press the spool on the seat.When the boiler pressure exceeds the pressure exerted by the spring on the upper part of the spool, the spool and stem are lifted and steam is discharged.When the boiler pressure is lower than the spring pressure acting on the upper part of the spool, the spool falls on the seat and the boiler stops discharging steam.The spool is a cone with a slight protrusion around the edge of the spool.When the steam opens the valve core, the e...
96
2018 - 10 - 16
A, definitions,Spring steel refers to the steel specially used to make spring elastic elements due to its elasticity in the quenching and tempering states.The elasticity of steel depends on its elastic deformation capacity, that is, within the specified range, the elastic deformation capacity makes it bear a certain load, and no permanent deformation occurs after the load is removed.Spring steel shall have excellent comprehensive performance, such as mechanical properties (especially elastic limit, strength limit and yield ratio), anti-elastic and anti-elastic properties (i.e. anti-elastic and...
97
2018 - 10 - 26
Most widely used, in manufacturing, the spiral wound into a separate ring, so that each ring gap (pitch), so that force contraction, to maintain tension to the two ends.When under the maximum load, it cannot be completely compressed, and the gap must be kept between effective turns to avoid friction or other material embedding, causing fatigue damage.The free length of the spring should be equal to the solid length of the spring plus the gap and the amount of deformation.To increase the contact surface of the compression spring, the surface should be ground to obtain 60~80% contact surface.Its...
98
2019 - 12 - 30
Spring design and its fabrication play an important role in manufacturing and industry around the globe. Springs come in all shapes and sizes to meet industry needs and are made from a wide range of metal alloys. Materials used for spring design and wire forming consist of high strength alloys.In general, wire formed into springs is cold rolled or drawn, and a made of medium to high carbon steel with high yield strength that allows for excellent elastic properties.Mechanical PropertiesThe mechanical principles of springs are very basic. They are an elastic component. Potential mechanical ...
99
2018 - 07 - 30
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30...
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 34
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 47
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 16
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者: nelson
发布时间: 2018 / 09 / 03
点击次数: 56
In order to remove the detergent, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and easy to remove dirt - wash with soap, weak lotion or warm water.Label and film: scrub with warm water and weak detergent.Binder composition - using alcohol or organic solution;Fat, oil, lubricating oil contamination - with a soft cloth or paper after drying with a neutral detergent or ammonia solution or special detergent to wash;Bleaching agent and seed acid adherence - immediately rinse with water, soak in ammonia or neutral soda solution, then wash with neutral detergent or warm water;Adhesion of organic carbides - soak in a hot neutral detergent or ammonia solution and then wash with a detergent containing a weak abrasive.Fingerprints dry with alcohol o...
作者: nelson
发布时间: 2018 / 09 / 03
点击次数: 81
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compress the spring to the test load once before the formal test. When the test load is heavier than the pressure and the load, the test load is the pressure and the load, but the maximum pressure and the ...
作者: nelson
发布时间: 2018 / 08 / 31
点击次数: 86
1. Shape effect is mainly caused by design factors, such as small fillet R, inappropriate location of acupoints, poor cross-sectional transition. 2. Overheating (overheating) is mainly caused by improper temperature control or running temperature, excessive process setting temperature, uneven furnace temperature and other factors. Preventive measures include overhaul, calibration of temperature control system, correction of process temperature, the addition of pad iron between the workpiece and furnace floor, etc.3. Decarbonization is mainly caused by overheating (or overburning), unprotected heating of air furnace, small machine surplus, residual decarbonization layer of forging or preparatory heat treatment, etc. The preventive measures are controlled atmosphere heating, salt bath h...
作者: nelson
发布时间: 2018 / 08 / 31
点击次数: 26
Spring drawings should be audited as follows: geometric parameters audit; physical parameters audit; technical conditions audit.(1) geometric parameters include material size, spring diameter, spring coil number, free height, spring rotation and so on.(2) physical parameters include load, stiffness, theoretical value of deformation, tolerance and so on.(3) Technical conditions include geometric tolerance, heat treatment process requirements, surface treatment, elastic compression treatment and shot peening treatment.
作者: nelson
发布时间: 2018 / 08 / 30
点击次数: 26
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compress the spring to the test load once before the formal test. When the test load is heavier than the pressure and the load, the test load is the pressure and the load, but the maximum pressure and the ...
作者: nelson
发布时间: 2018 / 08 / 29
点击次数: 116
In view of the harm caused by the surface defects of high carbon steel wire rods, the surface defects of high carbon steel wire rods were systematically analyzed by means of surface pickling, metallographic analysis and scanning electron microscopy, the types of defects were determined, the causes of defects were analyzed, and the improvement measures were put forward. After the implementation of these measures, the surface defects of high carbon steel wire rods were basically eliminated. Surface quality defects. The conclusions are as follows: 1. The surface defects found in high carbon steel wire rods are mainly related to rolling folding and hot scratch. The main measures are to adjust the gap between the rolls of the middle rolling mill and the reducing sizing mill RSM, to repair ...
作者: nelson
发布时间: 2018 / 08 / 28
点击次数: 32
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spring process has to be cut off, a spring connected to several springs is separated into a single spring.Some important springs can add a blank height classification procedure before grinding the face t...
作者: nelson
发布时间: 2018 / 08 / 27
点击次数: 35
Core tip: the surface of spring can be generally treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film dacroa DACROMET dacroa protective layer has excellent corrosion resistance, which is 710 times the corrosion resistance of the traditional electroplating layer, and there is no hydrogen embrittlement in the electroplating process. Generally, the surface of springs can be treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film "dacrom DACROMET dacroa protective layer" has excellent corrosion resistance, which is 7-10 times the corrosion resistance of traditional electroplating layer, and there is no hydrogen embrittlement of electroplati...
作者: nelson
发布时间: 2018 / 08 / 25
点击次数: 33
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
155页次11/18首页PrePage...  6789101112131415...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat