HOT INFORMATION
<
  • 2018 . 10 . 19
    402
    Daisy
    1、 preparation before peening1) the size and surface roughness before spring-shot blasting should meet the requirements of the pattern, except for special instructions (if it is necessary to reprocess the shot blasting surface).2) the spring shall complete the prescribed heat treatment before shot peening.3) the non-destructive test of the spring shall be completed before the shot peening treatment, or after the shot peening if there is special requirement.4) the surface of the spring to be sprayed should be clean, dry and free of oil.2、 treatment after shot peening1) the heating temperature of the spring parts shall not exceed 250~E, and the heating temperature of the spring parts shall not exceed 400~C for stainless steel.2) the spring after shot peening is allowed to be modified mechani...
  • 2018 . 10 . 18
    393
    Daisy
    With the rapid development of technology, spring's figure is everywhere, playing an irreplaceable role in all walks of life.How to use the properties of the spring itself according to local conditions will be today's small talk about the content.Spring measuring functionWe know that, within the elastic limit, the extension (or contraction) of the stretching spring, compression spring, torsion spring, bending spring, spring and spiral spring is proportional to the force.A spring scale is made from the property of a spring.Spring compression functionObserving various electrical switches, it is found that one of the two contacts of the switch must have a spring in the head to ensure that the two heads are in close contact and conduct well.If the contact is not good, the resistance at ...
  • 2018 . 10 . 18
    286
    Daisy
    For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle fracture.Iii. Tensile spring fatigue fractureSpring fracture under cyclic loading.Iv. Hydrogen embrittlement, cadmium embrittlement and black embrittlement:Brittle break due to high content of impurit...
  • 2018 . 10 . 17
    299
    Daisy
    A compact protective film is formed on the surface of the spring by chemical reaction to prevent the corrosion of the spring.Generally, oxidation treatment and phosphating treatment are used.Oxidation treatment and phosphating treatment have low cost and high production efficiency. Generally, spring manufacturers adopt oxidation treatment as corrosion prevention treatment.1.Oxidation treatment of steel is also known as bluing, blackening and boiling black.After oxidation treatment, the surface of the spring produces protective magnetic iron oxide, which is generally blue or black or sometimes dark brown.The color depends on the surface state of the spring, the chemical composition of the spring material and the oxidation process.The methods of oxidation treatment include alkaline oxidation...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
73
2018 - 08 - 14
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by ca...
74
2018 - 08 - 25
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
75
2018 - 09 - 10
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
76
2018 - 09 - 21
Compression springs are frequently seen and used in daily life. The main principle of compression springs is to provide a hand to the machine and drive it to work.The compression spring has a certain damping capacity, because the product's elastic force is not a fixed value, so every time it is used, there will be a return force, and the force is not a fixed size, which to some extent has the ability to slow down the vibration.As an example, now the car is installed above a compression spring, you will find when driving, its speed is greatly improved, and the movement process there is no s...
77
2018 - 10 - 08
The oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then ma...
78
2018 - 10 - 18
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle ...
79
2018 - 11 - 01
1) make it clear whether to use raw drawn steel wire or lead hardened steel wire;2) propose the requirements of steel wire diameter, strength grade (group) and standard number (select according to table 1.1);3) if there are special requirements such as strength and diameter allowable error, etc. (standard parameters are in parts 2 and 3);4) special packaging and marking requirements (see 1.4);5) carbon steel spring suitable for long-term work under the condition of temperature 121 ℃, highest working temperature should be chosen alloy spring steel.3 special needsShaped cross section: square, re...
80
2020 - 01 - 13
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be...
81
2018 - 07 - 14
Spring is one of the most commonly used parts in the mechanical and electronic products industry. It can produce very large elastic deformation when it is loaded, and this elastic deformation also transforms mechanical work or kinetic energy into deformation energy, which can unload the change of spring, and disappear and return to the original shape, finally, finally. Transformation of deformation energy into mechanical work or kinetic energy. With the continuous progress of the times, the application of spring is very wide, the automobile, computer, TV, pin, phone, cell phone and so on are u...
NEW INFORMATION / More
73
2018 - 08 - 02
M- mass of the object acting on the spring (kg)Ms- spring mass (kg)  N- variable load cycle number  N- spring working circle  Nz- spring support ring number  N1- total number of turns of the spring  P'- Spring single ring stiffness (N/mm)  R- The middle radius of the coil (mm)  R1- inner radius of the coil (mm)  R2- outer radius of the coil (mm)  R- damping coefficient  S- safety factor  T-torque; torque (Nmm)  T'- torsional stiffness (N-mm /(0))T- spring momentTc- cable p...
74
2018 - 08 - 16
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
75
2018 - 08 - 31
Spring drawings should be audited as follows: geometric parameters audit; physical parameters audit; technical conditions audit.(1) geometric parameters include material size, spring diameter, spring coil number, free height, spring rotation and so on.(2) physical parameters include load, stiffness, theoretical value of deformation, tolerance and so on.(3) Technical conditions include geometric tolerance, heat treatment process requirements, surface treatment, elastic compression treatment and shot peening treatment.
76
2018 - 09 - 13
The surface of steel is hardenedIn some parts, the surface layer of the workpiece bears higher stress than the core under the action of alternating loads such as torsion and bending and impact loads.In the case of friction, the surface layer is also constantly worn. Therefore, high strength, high hardness, high wear resistance and high fatigue limit are put forward for some surface layer of parts. Only surface strengthening can meet the above requirements.Because surface quenching has the advantages of small deformation and high productivity, it is widely used in production.According to differ...
77
2018 - 09 - 25
Torsion spring is a mechanical force storage structure, mainly used in ancient crossbow guns and other crossbow.The torsion spring accumulates the force through the twist or rotation of the elastic material with a relatively soft and pliable material, and makes use of it so that the projectile has certain mechanical energy.The modern torsion spring torsion bar is made of excellent elastic steel, and the form is also changed a lot, including the wire on the inner surface of the mechanical watch, the power spring in the toy gyroscope gun, as well as the torsion bar in the tank and car.Small...
78
2018 - 10 - 10
In recent years, the surface of the spring has been treated by the spring designers.The finishing (finishing) process is to put the spring directly into a series of finishing machines, such as tilting centrifugal type or spiral vibrating type, eddy current type, and add appropriate grinding materials, grinding agents and water for finishing.General optical finishing is about 20 to 30min. Specific optical finishing time depends on the spring shape and the amount of device.After finishing the finish, remove the spring and rinse it with tap water, then immerse in the SM series water film replacem...
79
2018 - 10 - 20
1) the selection basis of environmental factors in the use state of spring products: corrosion resistance, acid corrosion resistance, alkali corrosion resistance, salt corrosion resistance, water corrosion resistance, etc.Weather resistance;Resistance to stress and corrosion, fatigue and corrosion, etc.Wear resistance;Temperature resistance, etc.Radiation resistance, etc.2) selection basis of load characteristics of spring products: dynamic pulse-type cycle load, variable load, impact load, corrosion fatigue load, static load, large load and fatigue load, etc.3) selection basis of mechanical p...
80
2018 - 11 - 03
In the transmission mechanism of the press, when the clutch and the brake adopt mechanical rigid interlock, as long as the air is set on the clutch.The cylinder, the air pressure ACTS on the piston of the cylinder to make the clutch friction pair fit, and to make the air pressure of the spring brake brake friction pair separate and not brake, so when the air cylinder enters, the brake friction pair should be separated first, and then the clutch friction pair fits to complete the combination.The friction pair separation of the clutch and the friction pair fitting of the brake are respectively a...
81
2018 - 04 - 18
We do cherish the time together with all of our esteemed customers.  The picture shows the progressive hour withOne of our French customer who focus on the water purification system industry.
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 80
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 102
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 40
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者: Daisy
发布时间: 2018 / 09 / 18
点击次数: 61
1) make it clear whether to use raw drawn steel wire or lead hardened steel wire;2) propose the requirements of steel wire diameter, strength grade (group) and standard number (select according to table 1.1);3) if there are special requirements such as strength and diameter allowable error, etc. (standard parameters are in parts 2 and 3);4) special packaging and marking requirements (see 1.4);5) carbon steel spring suitable for long-term work under the condition of temperature 121 ℃, highest working temperature should be chosen alloy spring steel.3 special needsShaped cross section: square, rectangle, hexagonal, etc.Annealing treatment: suitable for large deformation and plasticity, such as flattening and triangulation.Stabilization treatment: the steel wire will be straightened after bein...
作者: Daisy
发布时间: 2018 / 09 / 17
点击次数: 74
Hard inspection method for chemical heat treatment and surface quenching and temperingSurface heat treatment is divided into two categories, one is chemical heat treatment and the other is surface quenching and tempering heat treatment. The hardness test method is as follows:1. Chemical heat treatmentChemical heat treatment is to make the workpiece surface infiltrate one or several chemical elements of the atom, thereby changing the workpiece surface chemical composition, organization and performance.After quenching and tempering, the surface of the workpiece has high hardness, wear resistance and contact fatigue strength, and the core of the workpiece has high toughness.The main technical parameters of chemical heat treatment workpiece are the depth of hardened layer and surface hardness....
作者: Daisy
发布时间: 2018 / 09 / 17
点击次数: 64
(1) metal tissue1. Metal: it has good thermal and electrical conductivity with opaque and metallic luster, and its electrical conductivity decreases with the increase of temperature, and it is rich in ductility and malleability.A solid (or crystal) in which the atoms of a metal are regularly arranged.2. Alloy: a substance which is composed of two or more metals or metals and non-metals and has metal properties.3. Phase: components with the same composition, structure and performance in the alloy.Solid solution: an atom (compound) of one (or several) element dissolves into the lattice of another element, while a solid metal crystal of the lattice type of the other element remains.5. Solid solution strengthening: as solute atoms enter the gap or junction of solvent lattice, the lattice is di...
作者: Daisy
发布时间: 2018 / 09 / 14
点击次数: 89
55SiCr is the high-grade steel used for automobile suspension springs. The suspension springs bear the reciprocating compression motion in the process of automobile driving, and play the role of buffer and shock absorption, which has high requirements on the performance of steel.Decarburization is one of the main problems in the hot processing of spring steel. Decarburization of spring steel surface will seriously damage the fatigue performance of spring, especially when the total decarburization of ferrite occurs on spring steel surface, the fatigue limit of spring can be reduced by 50%.At present, studies on decarburization of spring steel surface mainly focus on two influencing factors of heating temperature and heating time, while studies on the effect of heating furnace atmosphere on ...
作者: Daisy
发布时间: 2018 / 09 / 14
点击次数: 46
Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat treatment furnace design matches the design of the expert process control system.Eurotherm already has a unique knowledge of aviation and automotive heat treatment specifications.These knowledge and s...
作者: Daisy
发布时间: 2018 / 09 / 13
点击次数: 60
The surface of steel is hardenedIn some parts, the surface layer of the workpiece bears higher stress than the core under the action of alternating loads such as torsion and bending and impact loads.In the case of friction, the surface layer is also constantly worn. Therefore, high strength, high hardness, high wear resistance and high fatigue limit are put forward for some surface layer of parts. Only surface strengthening can meet the above requirements.Because surface quenching has the advantages of small deformation and high productivity, it is widely used in production.According to different heating methods, surface quenching mainly includes induction heating, flame heating and electric contact heating.Quench by induction heatingInduction heating is to use electromagnetic induction to...
作者: Daisy
发布时间: 2018 / 09 / 12
点击次数: 65
There are many methods of construction of paint, most of which are used for springs in the following ways:(1) dip coating method dip coating method is to dip the spring into the paint groove, and then take out, and let the excess paint on the surface drip naturally. After drying, it is covered with paint film on the surface of the spring.The dip-coating method has high production efficiency and can be applied to mechanization and automation production.But the paint volatilizes quickly, the paint that contains heavy quality pigment and two component paint material (amine solidify epoxy paint, polyurethane paint etc.) should not be used.Dip coating film is not smooth enough, easy to produce thin and thick, edge flow.(2) spraying method spraying is to use the spray gun to spray the paint into...
作者: Daisy
发布时间: 2018 / 09 / 12
点击次数: 59
Spring machine is now in the production of spring necessary equipment, due to the abundant of spring and the increase of precision is also more and more high to the requirement of spring machine, the spring machine maintenance is particularly important at ordinary times, and the main factors affecting the service life of spring machine has two, one is the operator of whether scientific and standardized operation, another is reasonable in daily maintenance.After using the spring machine for a period of time, the efficiency of the machine will be significantly reduced, affecting the efficiency of production. At this time, we should pay attention to the maintenance of the machine parts. Some seriously worn parts should be replaced in time.In the process of use, the inner part of the spring ma...
作者: Daisy
发布时间: 2018 / 09 / 11
点击次数: 43
Vibration damping spring is a common elastic component, which is widely used in various vibration equipment and automobile manufacturing industries. It has the advantages of good stability, low noise, good isolation effect and long service life.Compression springs, rubber springs, composite springs, air bag springs are vibration - reducing springs.Vibration damping spring can be divided into: wire compression spring, rubber spring, compound spring, rubber air spring, etc.Steel wire compression spring is a spiral spring under pressure, it USES the material section is mostly circular, also USES the rectangle and the multi-strand steel entangle to coil.Spring is commonly pitch, such as the shape of the compression spring are: cylindrical, conical, convex and concave and a small amount of rubb...
155页次9/18首页PrePage...  45678910111213...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat