您现在的位置： Home → News → Industry news

HOT INFORMATION / More

We’ll be the exhibitor of Manufacturing world Japan 2018 in Tokyo from June 20-23.

2018 - 04 - 18

To develope the new customer and enhance the exist business relationship, we’ll be exhibiting at the 22th MechaniceComponents&Material Technology Expo(M-Tech) in Tokyo Japan from JUNE 20-23. Your visiting at that timeIs highly welcomed!

What is the salt spray test?

2018 - 07 - 26

Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kin...

Material and characteristics of spring

2018 - 08 - 08

The spring is often subjected to variable load or impact load. In order to ensure that the spring can work permanently and reliably, the material must have high elastic limit and fatigue limit. At the same time, it should have enough toughness and plasticity and good heat treatment.Spring materials and properties can be consulted in relevant manuals, specifications and standards (GB/T129.6-92, GB4357-89). The common spring steel is mainly:1: carbon spring steelThis kind of spring (such as 65, 70 steel, etc.) has the advantages of cheap price, convenient source of raw materials, low elastic lim...

Inspection content and specification for spring parts(part 7)

2018 - 08 - 20

8.3.3 test machine should have the following functions: test time or preset function;Dynamic timing or counting function; test amplitude display or control function; automatic stop function.Evaluation of 8.4 spring fatigue test results8.4.1 fatigue life determination: under a given failure condition, the measured spring reachesThe maximum cycle number is the fatigue life of the spring.Verification of 8.4.2 fatigue life: if the number of cycles is tested, if the spring does not failThe validation test proved that the test was passed.8.4.3 reliability verification: according to the given reliabi...

Analysis of deformation prevention measures for heat treatment of metal spring

2018 - 09 - 04

There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount...

Hardness testing method for tempering heat treatment

2018 - 09 - 17

Hard inspection method for chemical heat treatment and surface quenching and temperingSurface heat treatment is divided into two categories, one is chemical heat treatment and the other is surface quenching and tempering heat treatment. The hardness test method is as follows:1. Chemical heat treatmentChemical heat treatment is to make the workpiece surface infiltrate one or several chemical elements of the atom, thereby changing the workpiece surface chemical composition, organization and performance.After quenching and tempering, the surface of the workpiece has high hardness, wear resistance...

Matters needing attention when choosing custom spring

2018 - 09 - 27

In order to make it convenient for customers to buy and custom spring, some brief introduction about spring and specification parameters are summarized as follows:The common spring can be classified as: stretching spiral spring, compression spiral spring and torsion spiral spring.Among them, stretch and compression springs are mostly produced in quantity, with complicated specifications but suitable for slight modifications. If a small amount of springs is needed and the characteristics of springs are not critical, they can be purchased easily in the market with a higher unit price.The users o...

Spring manufacturing process

2018 - 10 - 12

There are many ways of making spring, but the main forming part is cold forming and hot forming.In spring in the cold forming process, the spring mainly made by oil material toughening, lead bath quenching tempering spring wire, cold drawn wire, etc., using this kind of material in the manufacturing process of spring generally do not need special heat treatment and only requires the stress relieving, adopted by the spring design work stress and material performance.Spring cold forming process is generally suitable for special-shaped spring with small line diameter or more complicated shape, su...

Wire forming spring

2018 - 10 - 23

Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of ela...

NEW INFORMATION / More

We’ll be the exhibitor of Manufacturing world Japan 2018 in Tokyo from June 20-23.

2018 - 04 - 18

Summary of spring parameters and symbols (Part 3)

2018 - 08 - 02

Fr- spring radial load (N) Radial stiffness of the F'r-spring (N/mm) Fs- spring test load (N) F- Spring deformation (mm) Fj- deformation under working limit load Fj (mm) Fr- spring static deformation (mm) Fs- The amount of deformation of the spring under the test load Fs (mm); the amount of linear static deformation (mm) Fo- tension spring corresponds to the assumed deformation amount (mm) of the tensile force Fo; the central deformation amount of the diaphragm (mm) G-material shear modulus (MPa) &...

nspection content and specification for spring parts(part 2)

2018 - 08 - 15

Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is...

Steps of hardware spring pressure test

2018 - 08 - 30

The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compr...

Method of spring-surface paint

2018 - 09 - 12

There are many methods of construction of paint, most of which are used for springs in the following ways:(1) dip coating method dip coating method is to dip the spring into the paint groove, and then take out, and let the excess paint on the surface drip naturally. After drying, it is covered with paint film on the surface of the spring.The dip-coating method has high production efficiency and can be applied to mechanization and automation production.But the paint volatilizes quickly, the paint that contains heavy quality pigment and two component paint material (amine solidify epoxy paint, p...

Working characteristics of pressure spring

2018 - 09 - 25

Nowadays, with the development of science and technology, spring has become a very important hardware accessory in our life. Different products use different springs, and the longest used springs can be roughly divided into: pull spring, twist spring, press spring, disc spring and plate spring.The following features of a very practical tension spring:Many different products or hooks are used to guarantee the source of the tension of the tension spring. The tension spring works in the opposite way to the compression spring. The tension spring works in the opposite way when stretching or pulling...

Testing spring residual stress

2018 - 10 - 10

Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually ...

Spring calibration process

2018 - 10 - 20

After the end face grinding, if the free height, perpendicularity, pitch and outside diameter of the spring do not meet the deviation specified in the pattern, the screw compression spring often needs to be corrected.Calibration operations are generally manual or semi-manual.The commonly used tools are: the spring with the metal wire above 4mm, multi-purpose manual pressure machine, splitting machine, press and so on;For springs with wire under 4mm, special tools, pliers and hammers with wedge edge are often used.Calibration is to use these tools to make the spring locally plastic deformation ...

Electroplating after spring processing

2018 - 11 - 02

Zinc electroplating: zinc is stable in dry air and changes little. A white film of zinc oxide or carbon zinc carbonate is formed in moist air. This dense film will prevent further corrosion. Therefore, the galvanizing layer is used for the spring corrosion protection under general atmospheric conditions. Zinc coating should not be used for all springs that are in contact with solutions such as sulfuric acid, hydrochloric acid and caustic soda, as well as springs that work in humid air such as sulfur trioxide.Generally, passivation of galvanized coating can improve the protective performance of...

Consultation

hotline

86-755-28903525

Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.

Inspection content and specification for spring parts(part 2)

日期： 2018-07-28

浏览次数: 52

nelson

Detection of geometric size of 6.1 compression springs

6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.

6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is confirmed that the spring is upright. When the free height or length of the spring is greater than 500mm, the gauge is measured by ordinary steel tape and measured with vernier caliper or height gauge less than or equal to 500mm. When measuring with calipers, it is necessary to avoid excessive deformation caused by excessive clamping. The highest point or the longest point of the spring is the free height or free length of the spring.

Detection of the diameter of 6.1.3 spring: the spring in which the outer diameter and the size of the diameter are marked with the pattern, the spring with the diameter of the inner diameter is measured, the measured inner diameter is accurate, and the sample is marked with any more than one of the inner, middle and outer diameter of the spring, and the measured outer diameter is accurate. Except for special requirements for drawing, the size of the 1/4 ring at the two ends of the variable diameter spring shall be measured.

When measuring the diameter of the spring, the vernier calipers shall be used. One of the measuring paws should be contacted with the two reed rings at least, and the measuring paws should be kept perpendicular to the end ring plane. When the outer diameter is measured, the maximum point is measured. When the inner diameter is measured, the minimum point is determined. When the production of the spring is large, a special spring can be used to detect the sleeve or the axis of the heart. The quality of the end ring of the spring can be found by using the sleeve or the axis of the heart.

6.1.4 spring coil number detection: the number of springs is one - the same as visual inspection, when the total number of cycles is allowed.

When the error is less than or equal to 0.1 circle, it is detected with special measuring tool.

6.1.5 spring end clearance and end thickness detection: insert the feeler from the end gap, with the free passage. End thickness detection: insert the gauge into the gap of the spring with a feeler, and the end of the vernier caliper is perpendicular to the end, and the thickness of the end is measured.

6.1.6 spring pitch uniformity measurement: the total deformation of the spring is calculated according to the pattern, then the spring is placed on the load test machine to the specified amount of deformation, and the light is placed after the spring, and the normal pitch is judged according to the light transmittance.

6.1.7 spring pressure and height detection: press the spring on the load test machine and press it to measure its height.

6.1.8 spring surface detection: face grinding degree measurement: angle gauge to measure the grinding degree.

Detection of grinding surface roughness: it is permitted to compare and evaluate with other grinding surfaces tested.

6.1.9 spring perpendicularity test: the spring is placed vertically on the flat plate. In the non load state, the spring is rotating to the wide angle ruler one by one. The maximum gap between the spring end ring and the wide seat angle is found out (the end to the 1/2 circle is examined second adjacent circles), the size of the gap is measured with a tape measure, and the other end is measured after the end of the test.

The detection of the parallelism between the two ends of the 6.1.10 spring: the spring is placed vertically on the plate, and the indicator change of the surface of the end ring is measured with a dial indicator. The difference between the maximum and the minimum is the deviation of the parallelism between the rings at both ends of the spring.

Inspection content and specification for spring parts(part 1)

last：Inspection content and specification forNext：Inspection content and specification for

Relevant recommendations

Constant Force Spring

2020 . 01 . 13

Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant. Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound into a plane of the spiral of a spring, the spring is fixed at one end, the other end of the material after acting torque bending torque, bending elastic deformation, so the spring in its own plane to p...

Compression Springs

2020 . 01 . 13

A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be noted that if critical force-versus-deflection linearity is required, only the center 60-80% of the available deflection range should be employed.Thus, reserve at least the first and last 15-20% of t...

Spring wire materials

2020 . 01 . 06

When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension springs include carburetors, trampolines and farm machinery.Oil Tempered Spring WireOil tempered wire is cold drawn and heat treated before plating. Ideal as a general purpose spring wire, it is often us...

Compression spring,torsion spring,extension spring,wire forming spring

2020 . 01 . 06

springs are a mechanical part that use elasticity to work. Generally made of spring steel. It is widely used in machines and instruments to control the movement of machine parts, mitigate impact or vibration, store and store energy, measure force, etc.The spring is just an accumulator, it has the function of storing energy, but can not release the energy slowly, to achieve the release of this function should rely on the 'spring + large transmission ratio mechanism' to achieve, common in the mechanical table.The spring is widely used in the mechanical and electronic industry. The spring can produce a large elastic deformation under load and convert mechanical work or kinetic energy into deformation energy. After unloading, the spring's deformation disappears and returns to its o...