HOT INFORMATION
<
  • 2020 . 01 . 13
    79
    Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant.   Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound into a plane of the spiral of a spring, the spring is fixed at one end, the other end of the material after acting torque bending torque, bending elastic deformation, so the spring in its own plane to p...
  • 2020 . 01 . 13
    100
    A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be noted that if critical force-versus-deflection linearity is required, only the center 60-80% of the available deflection range should be employed.Thus, reserve at least the first and last 15-20% of t...
  • 2020 . 01 . 06
    39
    When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension springs include carburetors, trampolines and farm machinery.Oil Tempered Spring WireOil tempered wire is cold drawn and heat treated before plating. Ideal as a general purpose spring wire, it is often us...
  • 2020 . 01 . 06
    84
    springs are a mechanical part that use elasticity to work. Generally made of spring steel. It is widely used in machines and instruments to control the movement of machine parts, mitigate impact or vibration, store and store energy, measure force, etc.The spring is just an accumulator, it has the function of storing energy, but can not release the energy slowly, to achieve the release of this function should rely on the 'spring + large transmission ratio mechanism' to achieve, common in the mechanical table.The spring is widely used in the mechanical and electronic industry. The spring can produce a large elastic deformation under load and convert mechanical work or kinetic energy into deformation energy. After unloading, the spring's deformation disappears and returns to its o...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology

News NEWS INFORMATION
HOT INFORMATION / More
1
2018 - 07 - 13
Although the spring industry is a small industry in the whole manufacturing industry, its role must not be underestimated. The industrial manufacturing industry and the automobile industry in the country should accelerate the development, and the spring industry, as one of the basic parts and parts, needs to have a development over the early stage to adapt to the rapid development of the country's whole industry. In addition, the expansion of the spring product variety and the improvement of the quality level are also the needs of the replacement of machinery and equipment and the imp...
2
2018 - 07 - 31
8.3.3 test machine should have the following functions: test time or preset function;Dynamic timing or counting function; test amplitude display or control function; automatic stop function.Evaluation of 8.4 spring fatigue test results8.4.1 fatigue life determination: under a given failure condition, the measured spring reachesThe maximum cycle number is the fatigue life of the spring.Verification of 8.4.2 fatigue life: if the number of cycles is tested, if the spring does not failThe validation test proved that the test was passed.8.4.3 reliability verification: according to the given reliabi...
3
2018 - 08 - 14
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by ca...
4
2018 - 08 - 25
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
5
2018 - 09 - 10
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
6
2018 - 09 - 21
Compression springs are frequently seen and used in daily life. The main principle of compression springs is to provide a hand to the machine and drive it to work.The compression spring has a certain damping capacity, because the product's elastic force is not a fixed value, so every time it is used, there will be a return force, and the force is not a fixed size, which to some extent has the ability to slow down the vibration.As an example, now the car is installed above a compression spring, you will find when driving, its speed is greatly improved, and the movement process there is no s...
7
2018 - 10 - 08
The oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then ma...
8
2018 - 10 - 18
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle ...
9
2018 - 11 - 01
1) make it clear whether to use raw drawn steel wire or lead hardened steel wire;2) propose the requirements of steel wire diameter, strength grade (group) and standard number (select according to table 1.1);3) if there are special requirements such as strength and diameter allowable error, etc. (standard parameters are in parts 2 and 3);4) special packaging and marking requirements (see 1.4);5) carbon steel spring suitable for long-term work under the condition of temperature 121 ℃, highest working temperature should be chosen alloy spring steel.3 special needsShaped cross section: square, re...
NEW INFORMATION / More
1
2018 - 07 - 16
Torsional springs are a kind of helical springs, which mainly produce torque or rotational force. The end of the torsion spring is fixed to other components. When other components rotate around the center of the spring, the spring pullback them back to the initial position. Although this spring is called torsion spring, it is subject to bending stress rather than torsional stress. The torsion spring can store and release angular energy or fix a device in a static way by rotating the force arm around the middle axis of the spring body. Torsion springs are usually tight, but there is pitch betwe...
2
2018 - 08 - 08
Springs can also be classified by how they’re made. The first spring that comes to most people’s minds is probably a metal coil spring, also known as a helical spring. However, there are many other types. Even an elastic band can be considered a variable rate spring, since it stores mechanical energy. Coil SpringsLightweight coil springs are made by forming metal wires on an CNC coiling machine. The multi-axis CNC control allows you to create variable pitches and end conditions only limited by your imagination. Springs that come off the coiling machines do not have springy properties. They nee...
3
2018 - 08 - 21
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
4
2018 - 09 - 06
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
5
2018 - 09 - 18
Osmosis detection will be the basic principle of the spring of dip coating (penetrant) some penetration ability of the solution, the infiltration of surface defects, and then to remove excess penetrant, appeared in the surface layer of the tu yi agent again, at this point defects remaining in the penetrant sucked out, under the purple pay-off (fluorescence) observation or direct observation, can be found that the existence of defects.Osmotic detection can be used for the detection of ferromagnetic springs as well as non-ferromagnetic materials such as copper alloy and austenitic stainless stee...
6
2018 - 09 - 28
The special-shaped spring contains spring clip, tension spring and torsion spring, and the generalized special-shaped spring also includes snake spring, corrugated spring, bar spring and other complicated springs.Special-shaped spring is the basic part with wide application range and multifarious variety in automobile, motorcycle, electric appliance and instrument products. Its quality and life directly affect the performance of main engine products.Hyundai has made it a key component.Over 90% of special-shaped springs at home and abroad are made of two kinds of materials: lead quenched carbon...
7
2018 - 10 - 15
There are three ways to use stainless steel spring to remove oil and oxide skin:1. Immerse the stainless steel spring into the plastic container with the metal cleaning agent A diluted with water (the proportion of cleaning agent A and water dilution is 1:1 or 1:2), and the time should be as follows: the spring surface should be free from oil and oxide skin to restore the metal color. The soaking time should not be too long.So stainless steel spring surface has matte effect.2. In the ultrasonic equipment, the proportion of cleaning agent and water is about 1:30. It is advisable to restore the ...
8
2018 - 10 - 25
The spring relief valve is mainly composed of spool, seat, stem, spring and adjusting screw.The relief valve mainly USES spring force to press the spool on the seat.When the boiler pressure exceeds the pressure exerted by the spring on the upper part of the spool, the spool and stem are lifted and steam is discharged.When the boiler pressure is lower than the spring pressure acting on the upper part of the spool, the spool falls on the seat and the boiler stops discharging steam.The spool is a cone with a slight protrusion around the edge of the spool.When the steam opens the valve core, the e...
9
2019 - 12 - 23
Medical springs are an important component in the manufacturing of devices and equipment used throughout the medical industry. The three main types of springs used in medical devices—compression, torsion, and extension—and each serve a valuable purpose in varying types of equipment, large and small.Springs are devices that store mechanical energy. Though they are relatively simple in design, they are ubiquitous components in all kinds of devices and machines in a wide range of products from medical devices and equipment to consumer goods and heavy industrial equipment. Nearly anythin...
CONTACT US / More
hotline
86-755-28903526
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 79
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 100
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 39
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者:
发布时间: 2020 / 01 / 13
点击次数: 79
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant.   Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound into a plane of the spiral of a spring, the spring is fixed at one end, the other end of the material after acting torque bending torque, bending elastic deformation, so the spring in its own plane to p...
作者:
发布时间: 2020 / 01 / 13
点击次数: 100
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be noted that if critical force-versus-deflection linearity is required, only the center 60-80% of the available deflection range should be employed.Thus, reserve at least the first and last 15-20% of t...
作者:
发布时间: 2020 / 01 / 06
点击次数: 39
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension springs include carburetors, trampolines and farm machinery.Oil Tempered Spring WireOil tempered wire is cold drawn and heat treated before plating. Ideal as a general purpose spring wire, it is often us...
作者:
发布时间: 2020 / 01 / 06
点击次数: 84
springs are a mechanical part that use elasticity to work. Generally made of spring steel. It is widely used in machines and instruments to control the movement of machine parts, mitigate impact or vibration, store and store energy, measure force, etc.The spring is just an accumulator, it has the function of storing energy, but can not release the energy slowly, to achieve the release of this function should rely on the 'spring + large transmission ratio mechanism' to achieve, common in the mechanical table.The spring is widely used in the mechanical and electronic industry. The spring can produce a large elastic deformation under load and convert mechanical work or kinetic energy into deformation energy. After unloading, the spring's deformation disappears and returns to its o...
作者:
发布时间: 2019 / 12 / 30
点击次数: 104
1、What is Passivation?As a post-fabrication method, passivation is intended to maximize the natural corrosion resistance of stainless steel. Stainless steel is a steel alloy that contains a minimum of 10.5% chromium content by mass and along with a number of other alloys. When stainless steel is newly formed it needs to be cleaned of lubricants, oils, greases and other substances used in its fabrication. Once the steel has been cleaned it must be passivated. Passivation is a process that treats metal surfaces with an acid solution to make the surface corrosion resistant.Passive to atmospheric conditions by removing the free iron from the surface that causes corrosion. Once treated with an acid solution, slowly and naturally a passive layer develops on the surface of the steel as the chromi...
作者:
发布时间: 2019 / 12 / 30
点击次数: 43
Spring design and its fabrication play an important role in manufacturing and industry around the globe. Springs come in all shapes and sizes to meet industry needs and are made from a wide range of metal alloys. Materials used for spring design and wire forming consist of high strength alloys.In general, wire formed into springs is cold rolled or drawn, and a made of medium to high carbon steel with high yield strength that allows for excellent elastic properties.Mechanical PropertiesThe mechanical principles of springs are very basic. They are an elastic component. Potential mechanical energy is stored in the elastic materials of the spring while in a relaxed position.That energy is released and expended without any external power source through absorption or resistance only when it...
作者:
发布时间: 2019 / 12 / 23
点击次数: 54
Precision metal stamping is a cold-form manufacturing process that converts metal sheets into desired shapes—be it parts, components, or finished products—for a variety of applications. In metal fabrications shops or manufacturing operations, metal sheets, known as blanks, are fed through the tool and die surface of stamping presses to shape and shear the blanks into a finished three-dimensional object. Precision metal stamping services allow for mass production of complex parts in any quantity for nearly all industry.  The automotive industry, in building and construction, appliance manufacturing, aviation, energy, and many more industries rely on metal components produced by precision metal stamping utilizing various stamping techniques for production. Techniques...
作者:
发布时间: 2019 / 12 / 23
点击次数: 24
Medical springs are an important component in the manufacturing of devices and equipment used throughout the medical industry. The three main types of springs used in medical devices—compression, torsion, and extension—and each serve a valuable purpose in varying types of equipment, large and small.Springs are devices that store mechanical energy. Though they are relatively simple in design, they are ubiquitous components in all kinds of devices and machines in a wide range of products from medical devices and equipment to consumer goods and heavy industrial equipment. Nearly anything at all that involves a mechanism more than likely has a spring component.It is no surprise then that springs are an indispensable part in some of the most common and advanced medical equipment used ...
作者:
发布时间: 2019 / 12 / 16
点击次数: 47
Helical springsMaterials necessary for every aspect of daily life.  Helical spring is a spring that is subjected to torsional deformation, and its working part is also tightly wound into a helical shape. Its characteristic line is linear, can make compression spring, stretch spring and torsion spring. When the load is large and the radial size is limited, two compression springs with different diameters can be used together to become a combination spring. The total winding number n1 is the sum of the effective winding number n and the supporting winding number n2. Volute coil helical spring can store more energy and bear more load, but the manufacturing process is more complicated. The performance of the concave spiral spring is similar to that of the conical spiral spring.1. The...
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat