HOT INFORMATION
<
  • 2018 . 09 . 26
    50
    Daisy
    For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle fracture.Iii. extension spring fatigue fractureSpring fracture under cyclic loading.Iv. Hydrogen embrittlement, cadmium embrittlement and black embrittlement:Brittle break due to high content of impur...
  • 2018 . 09 . 25
    47
    Daisy
    Torsion spring is a mechanical force storage structure, mainly used in ancient crossbow guns and other crossbow.The torsion spring accumulates the force through the twist or rotation of the elastic material with a relatively soft and pliable material, and makes use of it so that the projectile has certain mechanical energy.The modern torsion spring torsion bar is made of excellent elastic steel, and the form is also changed a lot, including the wire on the inner surface of the mechanical watch, the power spring in the toy gyroscope gun, as well as the torsion bar in the tank and car.Small size of the torsion bar torque large, as a vehicle shock absorber tool better.Torsion spring is a relatively high precision spring accessories, production of torsion spring with normal spring machine...
  • 2018 . 09 . 25
    55
    Daisy
    Nowadays, with the development of science and technology, spring has become a very important hardware accessory in our life. Different products use different springs, and the longest used springs can be roughly divided into: pull spring, twist spring, press spring, disc spring and plate spring.The following features of a very practical tension spring:Many different products or hooks are used to guarantee the source of the tension of the tension spring. The tension spring works in the opposite way to the compression spring. The tension spring works in the opposite way when stretching or pulling.The tension spring is usually stretched to a certain extent, even when there is no load at all, and this initial tension determines the tightness of the tension spring without any load at all.The gre...
  • 2018 . 09 . 22
    78
    Daisy
    1) high strength: in order to improve the spring's ability to resist fatigue failure and relaxation, the spring material should have a high yield strength and elastic limit, and in particular, a high ratio of strength to strength.In general, the elastic limit of the material is directly proportional to the yield strength, so the spring design and the manufacturer always want the material to have a high yield strength.The tensile strength and yield strength of the spring material are close, for example, about 90% of the carbon steel wire of cold drawn is about: since the tensile strength is easier to be measured than the yield strength, the tensile strength is provided in the delivery of the material, so the tensile strength is generally used as the basis in design and manufacture.Howev...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
136
2018 - 07 - 23
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by ca...
137
2018 - 08 - 02
M- mass of the object acting on the spring (kg)Ms- spring mass (kg)  N- variable load cycle number  N- spring working circle  Nz- spring support ring number  N1- total number of turns of the spring  P'- Spring single ring stiffness (N/mm)  R- The middle radius of the coil (mm)  R1- inner radius of the coil (mm)  R2- outer radius of the coil (mm)  R- damping coefficient  S- safety factor  T-torque; torque (Nmm)  T'- torsional stiffness (N-mm /(0))T- spring momentTc- cable p...
138
2018 - 08 - 16
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
139
2018 - 08 - 30
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compr...
140
2018 - 09 - 12
There are many methods of construction of paint, most of which are used for springs in the following ways:(1) dip coating method dip coating method is to dip the spring into the paint groove, and then take out, and let the excess paint on the surface drip naturally. After drying, it is covered with paint film on the surface of the spring.The dip-coating method has high production efficiency and can be applied to mechanization and automation production.But the paint volatilizes quickly, the paint that contains heavy quality pigment and two component paint material (amine solidify epoxy paint, p...
141
2018 - 09 - 25
Nowadays, with the development of science and technology, spring has become a very important hardware accessory in our life. Different products use different springs, and the longest used springs can be roughly divided into: pull spring, twist spring, press spring, disc spring and plate spring.The following features of a very practical tension spring:Many different products or hooks are used to guarantee the source of the tension of the tension spring. The tension spring works in the opposite way to the compression spring. The tension spring works in the opposite way when stretching or pulling...
142
2018 - 10 - 10
Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually ...
143
2018 - 10 - 20
After the end face grinding, if the free height, perpendicularity, pitch and outside diameter of the spring do not meet the deviation specified in the pattern, the screw compression spring often needs to be corrected.Calibration operations are generally manual or semi-manual.The commonly used tools are: the spring with the metal wire above 4mm, multi-purpose manual pressure machine, splitting machine, press and so on;For springs with wire under 4mm, special tools, pliers and hammers with wedge edge are often used.Calibration is to use these tools to make the spring locally plastic deformation ...
144
2018 - 11 - 03
In the transmission mechanism of the press, when the clutch and the brake adopt mechanical rigid interlock, as long as the air is set on the clutch.The cylinder, the air pressure ACTS on the piston of the cylinder to make the clutch friction pair fit, and to make the air pressure of the spring brake brake friction pair separate and not brake, so when the air cylinder enters, the brake friction pair should be separated first, and then the clutch friction pair fits to complete the combination.The friction pair separation of the clutch and the friction pair fitting of the brake are respectively a...
NEW INFORMATION / More
136
2018 - 08 - 01
The basic spring parameters of the spring:1. Spring wire diameter D: wire diameter of spring.2. The outer diameter of the spring D2: the maximum outer diameter of the spring.3. The inner diameter of the spring D1: the smallest outer diameter of the spring.4. The middle diameter of the spring is D: the average diameter of the spring. Their calculation formula is: D= (D2+D1) +2=D1+d=D2-d5, pitch T: except for the support ring, the distance between the two adjacent circles of the spring corresponds to the axial distance on the middle diameter of the spring, and is expressed by t.6, effective circ...
137
2018 - 08 - 15
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in...
138
2018 - 08 - 29
In view of the harm caused by the surface defects of high carbon steel wire rods, the surface defects of high carbon steel wire rods were systematically analyzed by means of surface pickling, metallographic analysis and scanning electron microscopy, the types of defects were determined, the causes of defects were analyzed, and the improvement measures were put forward. After the implementation of these measures, the surface defects of high carbon steel wire rods were basically eliminated. Surface quality defects. The conclusions are as follows: 1. The surface defects found in high carbon ...
139
2018 - 09 - 12
Spring machine is now in the production of spring necessary equipment, due to the abundant of spring and the increase of precision is also more and more high to the requirement of spring machine, the spring machine maintenance is particularly important at ordinary times, and the main factors affecting the service life of spring machine has two, one is the operator of whether scientific and standardized operation, another is reasonable in daily maintenance.After using the spring machine for a period of time, the efficiency of the machine will be significantly reduced, affecting the efficiency o...
140
2018 - 09 - 22
1) high strength: in order to improve the spring's ability to resist fatigue failure and relaxation, the spring material should have a high yield strength and elastic limit, and in particular, a high ratio of strength to strength.In general, the elastic limit of the material is directly proportional to the yield strength, so the spring design and the manufacturer always want the material to have a high yield strength.The tensile strength and yield strength of the spring material are close, for example, about 90% of the carbon steel wire of cold drawn is about: since the tensile strength is...
141
2018 - 10 - 09
The paint used for the spring coating is usually of the following types:(1) asphalt paint has good water resistance, moisture resistance and corrosion resistance, especially excellent acid resistance and good alkali resistance.But adhesion, mechanical strength, poor decorative performance.(2) phenolic paint can be divided into two types: primer and topcoat. Phenolic primer has strong adhesion, good rust resistance, but poor mechanical strength and gloss.Phenolic coating film is hard, gloss good, but poor weather resistance, easy to yellow.(3) alkyd paint alkyd paint film is tough, with strong ...
142
2018 - 10 - 19
When the spring is made from materials that do not need to be hardened or tempered after forming, the process is spiral compression spring: rolling, de-stressed annealing, grinding of two ends, (shot blasting), (rectification), (de-stressed annealing), standing or strong pressure treatment, inspection, surface anti-corrosion treatment, packaging.Coil stretching spring: rolling, de-stress annealing, hook making, (cutting the tail), de-stress annealing, standing treatment, inspection, surface anti-corrosion treatment, packaging.Spiral torsion spring: rolling, de-stress annealing, torsion arm mak...
143
2018 - 11 - 02
Cylindrical spiral spring structureThere are three types of cylindrical spiral spring:1. Cylindrical spiral compression spring1) spacing between springsLet the spring's pitch be p;The diameter of the spring wire is d;In the free state, there should be proper spacing between the circles.In order to make the spring still maintain a certain elasticity after compression, it is also necessary to ensure that there is a certain gap of 1 between each circle under the maximum load.The size of lens 1 is generally recommended to be: in addition 1=0.1d or greater than 0.2mm2) dead circleThe two ends o...
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 57
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 69
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 25
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者: nelson
发布时间: 2018 / 07 / 28
点击次数: 36
Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is confirmed that the spring is upright. When the free height or length of the spring is greater than 500mm, the gauge is measured by ordinary steel tape and measured with vernier caliper or height gaug...
作者: nelson
发布时间: 2018 / 07 / 27
点击次数: 30
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in full. The inspector will inform the technician of the inspection result.4, Quality conformance testThe scope of application of the 4.1 whole test:4.1.1 Small batches of springs, such as less than 50 ...
作者: nelson
发布时间: 2018 / 07 / 26
点击次数: 40
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kind of test equipment with a certain volume space - salt spray test machine. In its volume space, the salt fog environment is used to test the salt spray corrosion resistance quality of the product. Com...
作者: nelson
发布时间: 2018 / 07 / 25
点击次数: 39
Core tip: the surface of spring can be generally treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film dacroa DACROMET dacroa protective layer has excellent corrosion resistance, which is 710 times the corrosion resistance of the traditional electroplating layer, and there is no hydrogen embrittlement in the electroplating process. Generally, the surface of springs can be treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film "dacrom DACROMET dacroa protective layer" has excellent corrosion resistance, which is 7-10 times the corrosion resistance of traditional electroplating layer, and there is no hydrogen embrittlement of electroplati...
作者: nelson
发布时间: 2018 / 07 / 25
点击次数: 26
1, matching springs and springs based on automobiles, motorcycles, diesel engines and gasoline engines. This type of spring has valve spring, suspension spring, damping spring and clutch spring, etc., with a large amount, which accounts for about 50% of the spring production. At the same time, the technical level is also high, it can be said that the technical level of these springs is representative, they are mainly to the high fatigue life and high anti relaxation direction, thus reducing the quality. 2. Large springs and plate springs, which mainly include railway rolling stock, heavy truck and engineering machinery, are mainly formed by hot coil forming, which is an important aspect of the spring manufacturing industry. With the development of high-speed railway and the upgrading ...
作者: nelson
发布时间: 2018 / 07 / 24
点击次数: 18
Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of elastic element widely used in the mechanical and electronic industry. When the spring is loaded, it can produce large elastic deformation and transform the mechanical work or kinetic energy into deforma...
作者: nelson
发布时间: 2018 / 07 / 24
点击次数: 26
(5) the development of spring steel wireAfter more than 100 years of development, the technology of spring steel has experienced lead hardened to oil quenching, and now it develops to induction hardening. Coupled with the continuous innovation and improvement of technology and equipment, the quality of varieties is constantly updated. The newly developed valves have been developed by induction heating and tempering with spring steel wire. It has been proved that the plastic, toughness, relaxation, fracture toughness, delayed fracture resistance, fatigue life and so on are all compared with oil quenched and tempered steel because of the short induction heating time, small quenching microstructure and almost no decarburization layer on the surface of steel wire. The silk has a great improvem...
作者:
发布时间: 2018 / 07 / 23
点击次数: 34
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by carbon element. In order to improve its special properties, Cu, Ti, Nb, Mn, Cr, Si and N elements can be added.2) the development of nitrogen containing stainless steel. The results of nitrogen generati...
作者: Nelson
发布时间: 2018 / 07 / 23
点击次数: 22
With the development of spring application technology, more requirements for spring materials are put forward. The main reason is to improve the fatigue life and anti relaxation performance under high stress; secondly, according to different uses, it is required for corrosion resistance, non magnetic, electrical conductivity, wear resistance, heat resistance and so on. In addition to the development of new varieties, the spring materials have achieved beneficial results in the aspects of strict control of chemical composition, reducing non-metallic inclusions, improving the surface quality and size accuracy.(1) development of the production process of spring steelIn order to improve the quality of spring steel, the industrial developed countries have generally adopted the refining technolo...
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat