HOT INFORMATION
<
  • 2018 . 10 . 29
    241
    Daisy
    The torsion spring is divided into single torsion spring and double torsion spring. The spring is usually inserted into the pin or shaft. When external force is applied, a torsion force is generated according to the shaft center of the spring to make the spring coiled tightly or loose.Double - twist spring is divided into external double - twist and internal double - torque spring.The loops are either closely encircled or separately encircled to allow for a load of torque (at right angles to the spring axis).The end of the spring can be wound into a hook or straight twist arm.The following is the necessary information of a torsion spring:(1) free length.(2) control diameter :(a) outside diameter, (b) inside diameter, (c) inside diameter of casing, or (d) outside diameter through round rod....
  • 2018 . 10 . 29
    258
    Daisy
    Each circle is formed into a tightly closed spiral ring or a pitch ring, which extends outwards when subjected to external forces and maintains a force of contraction towards the middle.There are many kinds of spring hooks: English hook, German hook, earring hook, fishtail hook, etc.(1) free length: (a) total length, (b) total length of the ring, and (c) length inside the hook ring.(2) control diameter :(a) outside diameter, (b) inside diameter, (c) inside diameter of casing.(3) steel wire size "wire diameter".(4) materials (type, grade).(5) winding number :(a) total winding number and (b) right or left turn.(6) terminal form.(7) load in the hook.(8) load rate, deflection, weight per inch.(9) maximum stretching length.The Extension Spring is a typical Spring, which can be shaped ...
  • 2018 . 10 . 26
    250
    Daisy
    Most widely used, in manufacturing, the spiral wound into a separate ring, so that each ring gap (pitch), so that force contraction, to maintain tension to the two ends.When under the maximum load, it cannot be completely compressed, and the gap must be kept between effective turns to avoid friction or other material embedding, causing fatigue damage.The free length of the spring should be equal to the solid length of the spring plus the gap and the amount of deformation.To increase the contact surface of the compression spring, the surface should be ground to obtain 60~80% contact surface.Its end has a variety of shapes: two seated rings, grinding equality at both ends.The two ends may be either open or closed or flat or worn because they are under pressure.The following is the necessary ...
  • 2018 . 10 . 26
    125
    Daisy
    Please avoid the improper way of using (1) more than the use of the maximum compression (300000 back to the conditions, after a close with the use of a long) stress causing the wreck, close to close with the use of a long, can make the spring line department gradually close to that, because of the high spring constant change caused by load curve with high, nearly and produce high stress to make spring break, please do not use more than 300000 times.The use of the spring without prepressure due to the gap caused the spring up and down vibration caused the spring distortion, if there is prepressure, the spring is relatively stable.When the spring is used, the pin and the spring will be worn and broken.When used without spring guide, the bottom of the spring and the body of the spring are eas...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
19
2018 - 09 - 27
In the actual work, we often encounter that the spring cannot push the moving object to the set position, that is to say, the length of the spring's computational freedom becomes shorter.The main reason is that there is no initial compression, that is, a spring is made into a spring, which is compressed to its compression height or to its compression height (if necessary) with a greater force, and cannot be restored to its original free length upon release.Its shortened quantity is called "initial compression quantity".After repeating 3-6 times of compression, the length is no longer...
20
2018 - 09 - 19
Spring machine is now in the production of spring necessary equipment, due to the abundant of spring and the increase of precision is also more and more high to the requirement of spring machine, the spring machine maintenance is particularly important at ordinary times, and the main factors affecting the service life of spring machine has two, one is the operator of whether scientific and standardized operation, another is reasonable in daily maintenance.After using the spring machine for a period of time, the efficiency of the machine will be significantly reduced, affecting the efficiency o...
21
2018 - 09 - 18
Osmosis detection will be the basic principle of the spring of dip coating (penetrant) some penetration ability of the solution, the infiltration of surface defects, and then to remove excess penetrant, appeared in the surface layer of the tu yi agent again, at this point defects remaining in the penetrant sucked out, under the purple pay-off (fluorescence) observation or direct observation, can be found that the existence of defects.Osmotic detection can be used for the detection of ferromagnetic springs as well as non-ferromagnetic materials such as copper alloy and austenitic stainless stee...
22
2018 - 09 - 10
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
23
2018 - 09 - 10
Spring grinding is easy to produce cracks at the end of the tightness, and directly affect the verticality of the spring, load and free length size, so the general grinding process of spring should be carried out after stress relief tempering. Eliminate the residual stress of steel wire cold drawing to prevent the generation of end gap cracks.The main factors that affect the quality of springs in grinding are as follows:(1) The grinding wheel should be selected reasonably; (2) the control of the bevel angle of the end ring; (3) a certain number of special measuring tools should be equipped to ...
24
2018 - 09 - 08
(1) heat treatment technology for strengthening springs.1) protective atmosphere heat treatment. In our country, protective atmosphere heat treatment is adopted in spring, oil quenched and tempered steel wire and toughened steel whose wire rod is less than 15mm. Heat treatment in protective atmosphere can remove surface decarbonization and oxidation and improve the surface quality of materials.2) induction heating or protective atmosphere induction heating heat treatment. This process is usually carried out on the wire before forming the coil spring. Some spring factories combine heat treatmen...
25
2018 - 09 - 11
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of ...
26
2018 - 09 - 11
Vibration damping spring is a common elastic component, which is widely used in various vibration equipment and automobile manufacturing industries. It has the advantages of good stability, low noise, good isolation effect and long service life.Compression springs, rubber springs, composite springs, air bag springs are vibration - reducing springs.Vibration damping spring can be divided into: wire compression spring, rubber spring, compound spring, rubber air spring, etc.Steel wire compression spring is a spiral spring under pressure, it USES the material section is mostly circular, also USES ...
27
2018 - 09 - 18
1) make it clear whether to use raw drawn steel wire or lead hardened steel wire;2) propose the requirements of steel wire diameter, strength grade (group) and standard number (select according to table 1.1);3) if there are special requirements such as strength and diameter allowable error, etc. (standard parameters are in parts 2 and 3);4) special packaging and marking requirements (see 1.4);5) carbon steel spring suitable for long-term work under the condition of temperature 121 ℃, highest working temperature should be chosen alloy spring steel.3 special needsShaped cross section: square, re...
NEW INFORMATION / More
19
2018 - 09 - 21
compression spring is under axial pressure of the spiral spring, it is used in the data section for more rounded, useful also rectangle and multi-strand steel rolled a travelling, spring is usually pitch, such as the shape of the compression spring are: cylindrical, conical, convex and concave and a small amount of noncircular, compression spring there is a certain gap between circle and circle, when under external load spring contraction deformation, deformation energy storage.The tension spring is a spiral spring that bears the axial tension.When there is no load, the stretch spring is usual...
20
2018 - 09 - 11
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of ...
21
2018 - 09 - 11
Vibration damping spring is a common elastic component, which is widely used in various vibration equipment and automobile manufacturing industries. It has the advantages of good stability, low noise, good isolation effect and long service life.Compression springs, rubber springs, composite springs, air bag springs are vibration - reducing springs.Vibration damping spring can be divided into: wire compression spring, rubber spring, compound spring, rubber air spring, etc.Steel wire compression spring is a spiral spring under pressure, it USES the material section is mostly circular, also USES ...
22
2018 - 09 - 12
Spring machine is now in the production of spring necessary equipment, due to the abundant of spring and the increase of precision is also more and more high to the requirement of spring machine, the spring machine maintenance is particularly important at ordinary times, and the main factors affecting the service life of spring machine has two, one is the operator of whether scientific and standardized operation, another is reasonable in daily maintenance.After using the spring machine for a period of time, the efficiency of the machine will be significantly reduced, affecting the efficiency o...
23
2018 - 09 - 12
There are many methods of construction of paint, most of which are used for springs in the following ways:(1) dip coating method dip coating method is to dip the spring into the paint groove, and then take out, and let the excess paint on the surface drip naturally. After drying, it is covered with paint film on the surface of the spring.The dip-coating method has high production efficiency and can be applied to mechanization and automation production.But the paint volatilizes quickly, the paint that contains heavy quality pigment and two component paint material (amine solidify epoxy paint, p...
24
2018 - 09 - 13
The surface of steel is hardenedIn some parts, the surface layer of the workpiece bears higher stress than the core under the action of alternating loads such as torsion and bending and impact loads.In the case of friction, the surface layer is also constantly worn. Therefore, high strength, high hardness, high wear resistance and high fatigue limit are put forward for some surface layer of parts. Only surface strengthening can meet the above requirements.Because surface quenching has the advantages of small deformation and high productivity, it is widely used in production.According to differ...
25
2018 - 09 - 14
Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat ...
26
2018 - 09 - 14
55SiCr is the high-grade steel used for automobile suspension springs. The suspension springs bear the reciprocating compression motion in the process of automobile driving, and play the role of buffer and shock absorption, which has high requirements on the performance of steel.Decarburization is one of the main problems in the hot processing of spring steel. Decarburization of spring steel surface will seriously damage the fatigue performance of spring, especially when the total decarburization of ferrite occurs on spring steel surface, the fatigue limit of spring can be reduced by 50%.At pr...
27
2018 - 09 - 17
(1) metal tissue1. Metal: it has good thermal and electrical conductivity with opaque and metallic luster, and its electrical conductivity decreases with the increase of temperature, and it is rich in ductility and malleability.A solid (or crystal) in which the atoms of a metal are regularly arranged.2. Alloy: a substance which is composed of two or more metals or metals and non-metals and has metal properties.3. Phase: components with the same composition, structure and performance in the alloy.Solid solution: an atom (compound) of one (or several) element dissolves into the lattice of anothe...
CONTACT US / More
hotline
86-755-28903525
Room 816, RongChao Financial Center, No 52, RuYi Road,LongCheng Street, LongGang District, ShenZhen,China.
Hot News / 热点新闻
2018 . 12 . 03
点击次数: 345
Today, the development of science and technology, spring has been a very important hardware accessories in our life, different products use the spring is not the same, the longest used spring can be r...
2018 . 11 . 03
点击次数: 259
Internal combustion engine valve spring, low, medium and high stress valve spring, safety valve spring, pressure reducing valve, electric regulating valve, pneumatic regulating valve, self-support reg...
2018 . 11 . 03
点击次数: 250
In the transmission mechanism of the press, when the clutch and the brake adopt mechanical rigid interlock, as long as the air is set on the clutch.The cylinder, the air pressure ACTS on the piston of...
作者: Daisy
发布时间: 2018 / 10 / 20
点击次数: 370
1) the selection basis of environmental factors in the use state of spring products: corrosion resistance, acid corrosion resistance, alkali corrosion resistance, salt corrosion resistance, water corrosion resistance, etc.Weather resistance;Resistance to stress and corrosion, fatigue and corrosion, etc.Wear resistance;Temperature resistance, etc.Radiation resistance, etc.2) selection basis of load characteristics of spring products: dynamic pulse-type cycle load, variable load, impact load, corrosion fatigue load, static load, large load and fatigue load, etc.3) selection basis of mechanical properties and strength characteristics of spring products: tensile strength, yield strength or flexure ratio, hardness, thermal hardness, reduction of section, elongation, impact toughness, relaxation...
作者: Daisy
发布时间: 2018 / 10 / 20
点击次数: 260
After the end face grinding, if the free height, perpendicularity, pitch and outside diameter of the spring do not meet the deviation specified in the pattern, the screw compression spring often needs to be corrected.Calibration operations are generally manual or semi-manual.The commonly used tools are: the spring with the metal wire above 4mm, multi-purpose manual pressure machine, splitting machine, press and so on;For springs with wire under 4mm, special tools, pliers and hammers with wedge edge are often used.Calibration is to use these tools to make the spring locally plastic deformation to achieve the required size of the pattern.1、 application of calibration process1) outside diameter correction.In general, coil spring can guarantee the deviation of outer diameter, but when the spri...
作者:
发布时间: 2018 / 10 / 19
点击次数: 3
When the spring is made from materials that do not need to be hardened or tempered after forming, the process is spiral compression spring: rolling, de-stressed annealing, grinding of two ends, (shot blasting), (rectification), (de-stressed annealing), standing or strong pressure treatment, inspection, surface anti-corrosion treatment, packaging.Coil stretching spring: rolling, de-stress annealing, hook making, (cutting the tail), de-stress annealing, standing treatment, inspection, surface anti-corrosion treatment, packaging.Spiral torsion spring: rolling, de-stress annealing, torsion arm making, cutting tail, de-stress annealing, standing treatment, inspection, surface anti-corrosion treatment, packaging.The manufacturing process of spiral drawing and torsion spring described above is to...
作者: Daisy
发布时间: 2018 / 10 / 19
点击次数: 349
1、 preparation before peening1) the size and surface roughness before spring-shot blasting should meet the requirements of the pattern, except for special instructions (if it is necessary to reprocess the shot blasting surface).2) the spring shall complete the prescribed heat treatment before shot peening.3) the non-destructive test of the spring shall be completed before the shot peening treatment, or after the shot peening if there is special requirement.4) the surface of the spring to be sprayed should be clean, dry and free of oil.2、 treatment after shot peening1) the heating temperature of the spring parts shall not exceed 250~E, and the heating temperature of the spring parts shall not exceed 400~C for stainless steel.2) the spring after shot peening is allowed to be modified mechani...
作者: Daisy
发布时间: 2018 / 10 / 18
点击次数: 347
With the rapid development of technology, spring's figure is everywhere, playing an irreplaceable role in all walks of life.How to use the properties of the spring itself according to local conditions will be today's small talk about the content.Spring measuring functionWe know that, within the elastic limit, the extension (or contraction) of the stretching spring, compression spring, torsion spring, bending spring, spring and spiral spring is proportional to the force.A spring scale is made from the property of a spring.Spring compression functionObserving various electrical switches, it is found that one of the two contacts of the switch must have a spring in the head to ensure that the two heads are in close contact and conduct well.If the contact is not good, the resistance at the cont...
作者: Daisy
发布时间: 2018 / 10 / 18
点击次数: 260
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle fracture.Iii. Tensile spring fatigue fractureSpring fracture under cyclic loading.Iv. Hydrogen embrittlement, cadmium embrittlement and black embrittlement:Brittle break due to high content of impurit...
作者: Daisy
发布时间: 2018 / 10 / 17
点击次数: 261
A compact protective film is formed on the surface of the spring by chemical reaction to prevent the corrosion of the spring.Generally, oxidation treatment and phosphating treatment are used.Oxidation treatment and phosphating treatment have low cost and high production efficiency. Generally, spring manufacturers adopt oxidation treatment as corrosion prevention treatment.1.Oxidation treatment of steel is also known as bluing, blackening and boiling black.After oxidation treatment, the surface of the spring produces protective magnetic iron oxide, which is generally blue or black or sometimes dark brown.The color depends on the surface state of the spring, the chemical composition of the spring material and the oxidation process.The methods of oxidation treatment include alkaline oxidation...
作者: Daisy
发布时间: 2018 / 10 / 17
点击次数: 259
Washing method according to the surface state:General considerationsWhen washing, please pay attention not to scratch the surface to avoid using the bleaching ingredients and the cleaning solution containing abrasive agent, steel ball (brush roller ball), grinding tools, etc. In order to remove the cleaning solution, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and dirt are washed with soap, a mild detergent, or warm waterLabel and film with warm water, weak detergent to scrubThe binder ingredient is alcohol or organic solutionUse a mild cloth or paper to dry and then wash with a neutral detergent or an ammonia solution or a special detergentRinse immediately with water, soak in an aqueous solution of ammonia or neutral carbonated soda, a...
作者: Daisy
发布时间: 2018 / 10 / 16
点击次数: 248
A, definitions,Spring steel refers to the steel specially used to make spring elastic elements due to its elasticity in the quenching and tempering states.The elasticity of steel depends on its elastic deformation capacity, that is, within the specified range, the elastic deformation capacity makes it bear a certain load, and no permanent deformation occurs after the load is removed.Spring steel shall have excellent comprehensive performance, such as mechanical properties (especially elastic limit, strength limit and yield ratio), anti-elastic and anti-elastic properties (i.e. anti-elastic and anti-loose properties), fatigue properties, quenching properties, physical and chemical properties (heat resistance, low temperature resistance, oxidation resistance, corrosion resistance, etc.).In o...
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat