HOT INFORMATION
<
  • 2018 . 10 . 15
    379
    Daisy
    (1) deformation heat treatment -- the combination of deformation reinforcement and heat treatment enhancement to further improve the strength and toughness of steel.Heat treatment of deformation has high, medium and low temperature.The high temperature deformation heat treatment is to produce the deformation immediately after the austenitic state at a stable distance, or can be combined with forging or hot rolling, that is, quenching immediately after hot forming.The deformation heat treatment has been applied to automobile plate spring production.(60 si2mn)(2) isothermal quenching of spring -- isothermal quenching can be adopted for springs with small diameter or sufficient permeability. It can not only reduce deformation, but also improve strength and toughness. It is better to conduct a...
  • 2018 . 10 . 12
    367
    Daisy
    There are many ways of making spring, but the main forming part is cold forming and hot forming.In spring in the cold forming process, the spring mainly made by oil material toughening, lead bath quenching tempering spring wire, cold drawn wire, etc., using this kind of material in the manufacturing process of spring generally do not need special heat treatment and only requires the stress relieving, adopted by the spring design work stress and material performance.Spring cold forming process is generally suitable for special-shaped spring with small line diameter or more complicated shape, such as line diameter less than 15mm, various kinds of snap, pull, twist spring, convex, concave and arc spring, etc.The cold forming process is simple and avoids the deformation and decarburization of ...
  • 2018 . 10 . 12
    280
    Daisy
    The spring is often corroded by the surrounding medium in the process of manufacture, storage and use.As the spring works under the influence of the spring force, the spring force will change and lose its function after being corroded.Therefore, preventing the corrosion of the spring can guarantee the stability of the spring and extend its service life.The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, causing corrosion of the spring is called chemical corrosion.For example, the spring is oxidized in the particu...
  • 2018 . 10 . 11
    395
    Daisy
    Type of paint used on spring surfacesThe oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then made of ferrous ironSodium sulfate interacts with sodium ferrite to form magnetic iron oxide (Pe3O4), or oxide film, with a thickness of about 0.5-1.5 microns.The co...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
91
2018 - 10 - 12
There are many ways of making spring, but the main forming part is cold forming and hot forming.In spring in the cold forming process, the spring mainly made by oil material toughening, lead bath quenching tempering spring wire, cold drawn wire, etc., using this kind of material in the manufacturing process of spring generally do not need special heat treatment and only requires the stress relieving, adopted by the spring design work stress and material performance.Spring cold forming process is generally suitable for special-shaped spring with small line diameter or more complicated shape, su...
92
2018 - 10 - 23
Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of ela...
93
2019 - 12 - 16
Helical springsMaterials necessary for every aspect of daily life.  Helical spring is a spring that is subjected to torsional deformation, and its working part is also tightly wound into a helical shape. Its characteristic line is linear, can make compression spring, stretch spring and torsion spring. When the load is large and the radial size is limited, two compression springs with different diameters can be used together to become a combination spring. The total winding number n1 is the sum of the effective winding number n and the supporting winding number n2. Volute coil helical...
94
2018 - 04 - 18
To grow the business, we need to develop management expertise and innovation across the team.Thia is the picture of AFR team development activity in one of the shenzhen beach, From the faceof young team,  we can see the confidence and what they want to achieve!
95
2018 - 07 - 27
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in...
96
2018 - 08 - 08
Springs can also be classified by how they’re made. The first spring that comes to most people’s minds is probably a metal coil spring, also known as a helical spring. However, there are many other types. Even an elastic band can be considered a variable rate spring, since it stores mechanical energy. Coil SpringsLightweight coil springs are made by forming metal wires on an CNC coiling machine. The multi-axis CNC control allows you to create variable pitches and end conditions only limited by your imagination. Springs that come off the coiling machines do not have springy properties. They nee...
97
2018 - 08 - 21
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
98
2018 - 09 - 05
1, matching springs and springs based on automobiles, motorcycles, diesel engines and gasoline engines. This type of spring has valve spring, suspension spring, damping spring and clutch spring, etc., with a large amount, which accounts for about 50% of the spring production. At the same time, the technical level is also high, it can be said that the technical level of these springs is representative, they are mainly to the high fatigue life and high anti relaxation direction, thus reducing the quality. 2. Large springs and plate springs, which mainly include railway rolling stock, heavy ...
99
2018 - 09 - 18
1) make it clear whether to use raw drawn steel wire or lead hardened steel wire;2) propose the requirements of steel wire diameter, strength grade (group) and standard number (select according to table 1.1);3) if there are special requirements such as strength and diameter allowable error, etc. (standard parameters are in parts 2 and 3);4) special packaging and marking requirements (see 1.4);5) carbon steel spring suitable for long-term work under the condition of temperature 121 ℃, highest working temperature should be chosen alloy spring steel.3 special needsShaped cross section: square, re...
NEW INFORMATION / More
91
2018 - 08 - 02
M- mass of the object acting on the spring (kg)Ms- spring mass (kg)  N- variable load cycle number  N- spring working circle  Nz- spring support ring number  N1- total number of turns of the spring  P'- Spring single ring stiffness (N/mm)  R- The middle radius of the coil (mm)  R1- inner radius of the coil (mm)  R2- outer radius of the coil (mm)  R- damping coefficient  S- safety factor  T-torque; torque (Nmm)  T'- torsional stiffness (N-mm /(0))T- spring momentTc- cable p...
92
2018 - 08 - 16
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
93
2018 - 08 - 31
Spring drawings should be audited as follows: geometric parameters audit; physical parameters audit; technical conditions audit.(1) geometric parameters include material size, spring diameter, spring coil number, free height, spring rotation and so on.(2) physical parameters include load, stiffness, theoretical value of deformation, tolerance and so on.(3) Technical conditions include geometric tolerance, heat treatment process requirements, surface treatment, elastic compression treatment and shot peening treatment.
94
2018 - 09 - 13
The surface of steel is hardenedIn some parts, the surface layer of the workpiece bears higher stress than the core under the action of alternating loads such as torsion and bending and impact loads.In the case of friction, the surface layer is also constantly worn. Therefore, high strength, high hardness, high wear resistance and high fatigue limit are put forward for some surface layer of parts. Only surface strengthening can meet the above requirements.Because surface quenching has the advantages of small deformation and high productivity, it is widely used in production.According to differ...
95
2018 - 09 - 25
Torsion spring is a mechanical force storage structure, mainly used in ancient crossbow guns and other crossbow.The torsion spring accumulates the force through the twist or rotation of the elastic material with a relatively soft and pliable material, and makes use of it so that the projectile has certain mechanical energy.The modern torsion spring torsion bar is made of excellent elastic steel, and the form is also changed a lot, including the wire on the inner surface of the mechanical watch, the power spring in the toy gyroscope gun, as well as the torsion bar in the tank and car.Small...
96
2018 - 10 - 10
In recent years, the surface of the spring has been treated by the spring designers.The finishing (finishing) process is to put the spring directly into a series of finishing machines, such as tilting centrifugal type or spiral vibrating type, eddy current type, and add appropriate grinding materials, grinding agents and water for finishing.General optical finishing is about 20 to 30min. Specific optical finishing time depends on the spring shape and the amount of device.After finishing the finish, remove the spring and rinse it with tap water, then immerse in the SM series water film replacem...
97
2018 - 10 - 20
1) the selection basis of environmental factors in the use state of spring products: corrosion resistance, acid corrosion resistance, alkali corrosion resistance, salt corrosion resistance, water corrosion resistance, etc.Weather resistance;Resistance to stress and corrosion, fatigue and corrosion, etc.Wear resistance;Temperature resistance, etc.Radiation resistance, etc.2) selection basis of load characteristics of spring products: dynamic pulse-type cycle load, variable load, impact load, corrosion fatigue load, static load, large load and fatigue load, etc.3) selection basis of mechanical p...
98
2018 - 11 - 03
In the transmission mechanism of the press, when the clutch and the brake adopt mechanical rigid interlock, as long as the air is set on the clutch.The cylinder, the air pressure ACTS on the piston of the cylinder to make the clutch friction pair fit, and to make the air pressure of the spring brake brake friction pair separate and not brake, so when the air cylinder enters, the brake friction pair should be separated first, and then the clutch friction pair fits to complete the combination.The friction pair separation of the clutch and the friction pair fitting of the brake are respectively a...
99
2018 - 04 - 18
We do cherish the time together with all of our esteemed customers.  The picture shows the progressive hour withOne of our French customer who focus on the water purification system industry.
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 77
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 95
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 37
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者: nelson
发布时间: 2018 / 09 / 03
点击次数: 64
In order to remove the detergent, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and easy to remove dirt - wash with soap, weak lotion or warm water.Label and film: scrub with warm water and weak detergent.Binder composition - using alcohol or organic solution;Fat, oil, lubricating oil contamination - with a soft cloth or paper after drying with a neutral detergent or ammonia solution or special detergent to wash;Bleaching agent and seed acid adherence - immediately rinse with water, soak in ammonia or neutral soda solution, then wash with neutral detergent or warm water;Adhesion of organic carbides - soak in a hot neutral detergent or ammonia solution and then wash with a detergent containing a weak abrasive.Fingerprints dry with alcohol o...
作者: nelson
发布时间: 2018 / 09 / 03
点击次数: 96
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compress the spring to the test load once before the formal test. When the test load is heavier than the pressure and the load, the test load is the pressure and the load, but the maximum pressure and the ...
作者: nelson
发布时间: 2018 / 08 / 31
点击次数: 113
1. Shape effect is mainly caused by design factors, such as small fillet R, inappropriate location of acupoints, poor cross-sectional transition. 2. Overheating (overheating) is mainly caused by improper temperature control or running temperature, excessive process setting temperature, uneven furnace temperature and other factors. Preventive measures include overhaul, calibration of temperature control system, correction of process temperature, the addition of pad iron between the workpiece and furnace floor, etc.3. Decarbonization is mainly caused by overheating (or overburning), unprotected heating of air furnace, small machine surplus, residual decarbonization layer of forging or preparatory heat treatment, etc. The preventive measures are controlled atmosphere heating, salt bath h...
作者: nelson
发布时间: 2018 / 08 / 31
点击次数: 42
Spring drawings should be audited as follows: geometric parameters audit; physical parameters audit; technical conditions audit.(1) geometric parameters include material size, spring diameter, spring coil number, free height, spring rotation and so on.(2) physical parameters include load, stiffness, theoretical value of deformation, tolerance and so on.(3) Technical conditions include geometric tolerance, heat treatment process requirements, surface treatment, elastic compression treatment and shot peening treatment.
作者: nelson
发布时间: 2018 / 08 / 30
点击次数: 29
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compress the spring to the test load once before the formal test. When the test load is heavier than the pressure and the load, the test load is the pressure and the load, but the maximum pressure and the ...
作者: nelson
发布时间: 2018 / 08 / 29
点击次数: 177
In view of the harm caused by the surface defects of high carbon steel wire rods, the surface defects of high carbon steel wire rods were systematically analyzed by means of surface pickling, metallographic analysis and scanning electron microscopy, the types of defects were determined, the causes of defects were analyzed, and the improvement measures were put forward. After the implementation of these measures, the surface defects of high carbon steel wire rods were basically eliminated. Surface quality defects. The conclusions are as follows: 1. The surface defects found in high carbon steel wire rods are mainly related to rolling folding and hot scratch. The main measures are to adjust the gap between the rolls of the middle rolling mill and the reducing sizing mill RSM, to repair ...
作者: nelson
发布时间: 2018 / 08 / 28
点击次数: 46
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spring process has to be cut off, a spring connected to several springs is separated into a single spring.Some important springs can add a blank height classification procedure before grinding the face t...
作者: nelson
发布时间: 2018 / 08 / 27
点击次数: 57
Core tip: the surface of spring can be generally treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film dacroa DACROMET dacroa protective layer has excellent corrosion resistance, which is 710 times the corrosion resistance of the traditional electroplating layer, and there is no hydrogen embrittlement in the electroplating process. Generally, the surface of springs can be treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film "dacrom DACROMET dacroa protective layer" has excellent corrosion resistance, which is 7-10 times the corrosion resistance of traditional electroplating layer, and there is no hydrogen embrittlement of electroplati...
作者: nelson
发布时间: 2018 / 08 / 25
点击次数: 42
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
158页次11/18首页PrePage...  6789101112131415...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat