HOT INFORMATION
<
  • 2018 . 10 . 17
    289
    Daisy
    Washing method according to the surface state:General considerationsWhen washing, please pay attention not to scratch the surface to avoid using the bleaching ingredients and the cleaning solution containing abrasive agent, steel ball (brush roller ball), grinding tools, etc. In order to remove the cleaning solution, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and dirt are washed with soap, a mild detergent, or warm waterLabel and film with warm water, weak detergent to scrubThe binder ingredient is alcohol or organic solutionUse a mild cloth or paper to dry and then wash with a neutral detergent or an ammonia solution or a special detergentRinse immediately with water, soak in an aqueous solution of ammonia or neutral carbonated soda, a...
  • 2018 . 10 . 16
    280
    Daisy
    A, definitions,Spring steel refers to the steel specially used to make spring elastic elements due to its elasticity in the quenching and tempering states.The elasticity of steel depends on its elastic deformation capacity, that is, within the specified range, the elastic deformation capacity makes it bear a certain load, and no permanent deformation occurs after the load is removed.Spring steel shall have excellent comprehensive performance, such as mechanical properties (especially elastic limit, strength limit and yield ratio), anti-elastic and anti-elastic properties (i.e. anti-elastic and anti-loose properties), fatigue properties, quenching properties, physical and chemical properties (heat resistance, low temperature resistance, oxidation resistance, corrosion resistance, etc.).In o...
  • 2018 . 10 . 16
    273
    Daisy
    The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension springs, should be preferentially used steel wire, cold-drawn steel wire such as strengthened steel wire, lead bath and oil hardened tempered steel wire, which has higher strength and good surface qua...
  • 2018 . 10 . 15
    334
    Daisy
    There are three ways to use stainless steel spring to remove oil and oxide skin:1. Immerse the stainless steel spring into the plastic container with the metal cleaning agent A diluted with water (the proportion of cleaning agent A and water dilution is 1:1 or 1:2), and the time should be as follows: the spring surface should be free from oil and oxide skin to restore the metal color. The soaking time should not be too long.So stainless steel spring surface has matte effect.2. In the ultrasonic equipment, the proportion of cleaning agent and water is about 1:30. It is advisable to restore the metal color without oil and oxide skin on the spring surface.The above two methods can be applied to high precision spring.3. After the cleaning agent A is put into the vibration polishing machine wit...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
82
2018 - 08 - 01
Core tips: elastic formula: F=kx, F for elastic, K for the stiffness coefficient, X for the length of the spring length, such as the length of the spring for example, to test a spring of 5N: 5N pull the stiffness coefficient of 100N/m spring, the spring is elongated 5cmF= KX, K is the stiffness coefficient (unit is Newton per meter), X is the spring elongation (unit is rice), this law is called Hooke's law.Elastic formula:F=kx, F is elastic, K is stiffness coefficient, X is spring stretch length.For example, to test a 5N spring:When a spring with a stiffness coefficient of 100N/m is pulled...
83
2018 - 08 - 14
(5) the development of spring steel wireAfter more than 100 years of development, the technology of spring steel has experienced lead hardened to oil quenching, and now it develops to induction hardening. Coupled with the continuous innovation and improvement of technology and equipment, the quality of varieties is constantly updated. The newly developed valves have been developed by induction heating and tempering with spring steel wire. It has been proved that the plastic, toughness, relaxation, fracture toughness, delayed fracture resistance, fatigue life and so on are all compared with oil...
84
2018 - 08 - 27
Core tip: the surface of spring can be generally treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film dacroa DACROMET dacroa protective layer has excellent corrosion resistance, which is 710 times the corrosion resistance of the traditional electroplating layer, and there is no hydrogen embrittlement in the electroplating process. Generally, the surface of springs can be treated, such as blackening (blue), phosphating, electroplating, spray molding, etc. In recent years, the zinc chromium film "dacrom DACROMET da...
85
2018 - 09 - 11
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
86
2018 - 09 - 21
compression spring is under axial pressure of the spiral spring, it is used in the data section for more rounded, useful also rectangle and multi-strand steel rolled a travelling, spring is usually pitch, such as the shape of the compression spring are: cylindrical, conical, convex and concave and a small amount of noncircular, compression spring there is a certain gap between circle and circle, when under external load spring contraction deformation, deformation energy storage.The tension spring is a spiral spring that bears the axial tension.When there is no load, the stretch spring is usual...
87
2018 - 10 - 08
The spring should ideally conform to hooke's law, that is, the relationship between stress and strain in the elastic range is linear.However, since the actual spring steel is a polyphase and polycrystalline material, there must be inconsistencies in composition, structure, elasticity, etc., and the stress and strain deviated from the linear relationship within the elastic range, which is called elastic incompleteness or anelastic.The phenomena such as elastic after effect, elastic lag, stress relaxation and elastic modulus decrease are produced.After tempering, the stabilization process ca...
88
2018 - 10 - 18
With the rapid development of technology, spring's figure is everywhere, playing an irreplaceable role in all walks of life.How to use the properties of the spring itself according to local conditions will be today's small talk about the content.Spring measuring functionWe know that, within the elastic limit, the extension (or contraction) of the stretching spring, compression spring, torsion spring, bending spring, spring and spiral spring is proportional to the force.A spring scale is made from the property of a spring.Spring compression functionObserving various electrical switches,...
89
2018 - 11 - 01
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
90
2020 - 01 - 13
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant.   Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound in...
NEW INFORMATION / More
82
2018 - 07 - 31
8, detection of fatigue property and relaxation rate of spring8.1 spring fatigue performance testing requirements: the spring that bears the variable load is in the internal quality of the enterprise.Quantity control, user inspection, new product certification, certification, industry sampling and process adjustment.In the ring section, the fatigue performance must be tested. The testing method can be tested by fatigue life testThere are two kinds of certificate test or reliability evaluation test, but they are classified and certified for products.Reliability evaluation test must be adopted t...
83
2018 - 08 - 13
With the development of spring application technology, more requirements for spring materials are put forward. The main reason is to improve the fatigue life and anti relaxation performance under high stress; secondly, according to different uses, it is required for corrosion resistance, non magnetic, electrical conductivity, wear resistance, heat resistance and so on. In addition to the development of new varieties, the spring materials have achieved beneficial results in the aspects of strict control of chemical composition, reducing non-metallic inclusions, improving the surface quality and...
84
2018 - 08 - 25
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
85
2018 - 09 - 10
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
86
2018 - 09 - 21
Compression springs are frequently seen and used in daily life. The main principle of compression springs is to provide a hand to the machine and drive it to work.The compression spring has a certain damping capacity, because the product's elastic force is not a fixed value, so every time it is used, there will be a return force, and the force is not a fixed size, which to some extent has the ability to slow down the vibration.As an example, now the car is installed above a compression spring, you will find when driving, its speed is greatly improved, and the movement process there is no s...
87
2018 - 10 - 08
The oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then ma...
88
2018 - 10 - 18
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle ...
89
2018 - 10 - 30
The ground spring is also a hydraulic door closer, except that it presses the spring with a worm gear rather than a rack and pinion.Because the worm wheel can be rotated in a positive and negative direction, the ground spring can be used for two-way open doors, while the door closer can only be used for one-way open doors.The technical key of the ground spring is the bearing seat at the lower part of the main shaft, which determines the bearing grade of the landing spring.Because the ground spring used for two-way doors carries the weight of the door, the weight of the door is crucial to the s...
90
2020 - 01 - 06
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension spr...
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 97
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 112
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 48
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者: nelson
发布时间: 2018 / 09 / 11
点击次数: 33
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
作者: Daisy
发布时间: 2018 / 09 / 10
点击次数: 37
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which is a chemical corrosion.If the spring is in contact with the electrolyte solution, the corrosion caused by the action of the micro battery is called electrochemical corrosion.For example, the spring is...
作者: nelson
发布时间: 2018 / 09 / 10
点击次数: 55
Spring grinding is easy to produce cracks at the end of the tightness, and directly affect the verticality of the spring, load and free length size, so the general grinding process of spring should be carried out after stress relief tempering. Eliminate the residual stress of steel wire cold drawing to prevent the generation of end gap cracks.The main factors that affect the quality of springs in grinding are as follows:(1) The grinding wheel should be selected reasonably; (2) the control of the bevel angle of the end ring; (3) a certain number of special measuring tools should be equipped to ensure the grinding quality; (4) the grinding wheel should be repaired in time; (5) the correct size of the grinding sleeve should be selected, and the gap between the spring and the sleeve should be ...
作者: nelson
发布时间: 2018 / 09 / 08
点击次数: 58
(1) heat treatment technology for strengthening springs.1) protective atmosphere heat treatment. In our country, protective atmosphere heat treatment is adopted in spring, oil quenched and tempered steel wire and toughened steel whose wire rod is less than 15mm. Heat treatment in protective atmosphere can remove surface decarbonization and oxidation and improve the surface quality of materials.2) induction heating or protective atmosphere induction heating heat treatment. This process is usually carried out on the wire before forming the coil spring. Some spring factories combine heat treatment of wire materials with spring making to reduce costs. Induction heating treatment has better strengthening effect, rapid induction heating speed, help to refine grain and reduce surface decarbonizat...
作者: nelson
发布时间: 2018 / 09 / 07
点击次数: 30
In the heat treatment of forgings, the way of placing parts to reduce deformation is to hang them vertically as far as possible, to place them vertically at the bottom of the furnace, to support them horizontally with two points, to place the fulcrum between one-third and one-fourth of the full length, and to place them flat on the heat-resistant steel tooling.In the cooling process of parts, the types, cooling properties and hardenability of quenching medium are related to deformation. The change of cooling performance can be adjusted by changing the viscosity, temperature, liquid pressure, additives and stirring of the medium. The higher the viscosity of quenching oil, the higher the temperature, the smaller the elliptical deformation. In static state, the deformation is small.The follow...
作者: nelson
发布时间: 2018 / 09 / 07
点击次数: 28
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount of shrinkage is directly proportional to the supersaturated carbon content. When heated at room temperature of -200, part of austenite is transformed into martensite and expanded. However, the expans...
作者: nelson
发布时间: 2018 / 09 / 06
点击次数: 38
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spring process has to be cut off, a spring connected to several springs is separated into a single spring.Some important springs can add a blank height classification procedure before grinding the face t...
作者: nelson
发布时间: 2018 / 09 / 05
点击次数: 37
1, matching springs and springs based on automobiles, motorcycles, diesel engines and gasoline engines. This type of spring has valve spring, suspension spring, damping spring and clutch spring, etc., with a large amount, which accounts for about 50% of the spring production. At the same time, the technical level is also high, it can be said that the technical level of these springs is representative, they are mainly to the high fatigue life and high anti relaxation direction, thus reducing the quality. 2. Large springs and plate springs, which mainly include railway rolling stock, heavy truck and engineering machinery, are mainly formed by hot coil forming, which is an important aspect of the spring manufacturing industry. With the development of high-speed railway and the upgrading ...
作者: nelson
发布时间: 2018 / 09 / 04
点击次数: 40
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount of shrinkage is directly proportional to the supersaturated carbon content. When heated at room temperature of -200, part of austenite is transformed into martensite and expanded. However, the expans...
158页次10/18首页PrePage...  567891011121314...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat