HOT INFORMATION
<
  • 2018 . 09 . 20
    89
    Daisy
    The purpose of mold spring is to take off material, press material, the strength of the spring, which is related to whether the mold production is smooth, whether the product is qualified.Spring force is small, may cause the product to be out of shape, the mold does not take off the material, the product is bad to take out from the mold inside, the belt material, the knife edge, punch easy to wear and so on each kind of question.Mold spring according to different production times, compression amount selected, the larger the spring life, the shorter die life, of course, the broken spring can be replaced, but the specifications of each spring are different, the design has been determined, springs in use do not easily replace each other.The moulds may run out of steam for a while, and the spr...
  • 2018 . 09 . 19
    78
    Daisy
    Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually obtained by the following two methods:(1) X-ray detection method.X ray detection is a non-destructive testing method. This method can detect residual stress on specific surfaces and sites, but it has ...
  • 2018 . 09 . 19
    94
    Daisy
    Spring machine is now in the production of spring necessary equipment, due to the abundant of spring and the increase of precision is also more and more high to the requirement of spring machine, the spring machine maintenance is particularly important at ordinary times, and the main factors affecting the service life of spring machine has two, one is the operator of whether scientific and standardized operation, another is reasonable in daily maintenance.After using the spring machine for a period of time, the efficiency of the machine will be significantly reduced, affecting the efficiency of production. At this time, we should pay attention to the maintenance of the machine parts. Some seriously worn parts should be replaced in time.In the process of use, the inner part of the spring ma...
  • 2018 . 09 . 18
    53
    Daisy
    Osmosis detection will be the basic principle of the spring of dip coating (penetrant) some penetration ability of the solution, the infiltration of surface defects, and then to remove excess penetrant, appeared in the surface layer of the tu yi agent again, at this point defects remaining in the penetrant sucked out, under the purple pay-off (fluorescence) observation or direct observation, can be found that the existence of defects.Osmotic detection can be used for the detection of ferromagnetic springs as well as non-ferromagnetic materials such as copper alloy and austenitic stainless steel springs.(1) oil immersion test can be used for spring whose diameter of wire is greater than 8mm.The spring that has been cleaned on the surface is immersed in kerosene, or the mixture of 50% (mass ...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology

News NEWS INFORMATION
HOT INFORMATION / More
145
2018 - 07 - 23
With the development of spring application technology, more requirements for spring materials are put forward. The main reason is to improve the fatigue life and anti relaxation performance under high stress; secondly, according to different uses, it is required for corrosion resistance, non magnetic, electrical conductivity, wear resistance, heat resistance and so on. In addition to the development of new varieties, the spring materials have achieved beneficial results in the aspects of strict control of chemical composition, reducing non-metallic inclusions, improving the surface quality and...
146
2018 - 08 - 02
Fr- spring radial load (N)  Radial stiffness of the F'r-spring (N/mm)  Fs- spring test load (N)  F- Spring deformation (mm)  Fj- deformation under working limit load Fj (mm)  Fr- spring static deformation (mm)  Fs- The amount of deformation of the spring under the test load Fs (mm); the amount of linear static deformation (mm)  Fo- tension spring corresponds to the assumed deformation amount (mm) of the tensile force Fo; the central deformation amount of the diaphragm (mm)  G-material shear modulus (MPa) &...
147
2018 - 08 - 15
Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is...
148
2018 - 08 - 29
In view of the harm caused by the surface defects of high carbon steel wire rods, the surface defects of high carbon steel wire rods were systematically analyzed by means of surface pickling, metallographic analysis and scanning electron microscopy, the types of defects were determined, the causes of defects were analyzed, and the improvement measures were put forward. After the implementation of these measures, the surface defects of high carbon steel wire rods were basically eliminated. Surface quality defects. The conclusions are as follows: 1. The surface defects found in high carbon ...
149
2018 - 09 - 12
Spring machine is now in the production of spring necessary equipment, due to the abundant of spring and the increase of precision is also more and more high to the requirement of spring machine, the spring machine maintenance is particularly important at ordinary times, and the main factors affecting the service life of spring machine has two, one is the operator of whether scientific and standardized operation, another is reasonable in daily maintenance.After using the spring machine for a period of time, the efficiency of the machine will be significantly reduced, affecting the efficiency o...
150
2018 - 09 - 22
1) high strength: in order to improve the spring's ability to resist fatigue failure and relaxation, the spring material should have a high yield strength and elastic limit, and in particular, a high ratio of strength to strength.In general, the elastic limit of the material is directly proportional to the yield strength, so the spring design and the manufacturer always want the material to have a high yield strength.The tensile strength and yield strength of the spring material are close, for example, about 90% of the carbon steel wire of cold drawn is about: since the tensile strength is...
151
2018 - 10 - 09
The paint used for the spring coating is usually of the following types:(1) asphalt paint has good water resistance, moisture resistance and corrosion resistance, especially excellent acid resistance and good alkali resistance.But adhesion, mechanical strength, poor decorative performance.(2) phenolic paint can be divided into two types: primer and topcoat. Phenolic primer has strong adhesion, good rust resistance, but poor mechanical strength and gloss.Phenolic coating film is hard, gloss good, but poor weather resistance, easy to yellow.(3) alkyd paint alkyd paint film is tough, with strong ...
152
2018 - 10 - 19
When the spring is made from materials that do not need to be hardened or tempered after forming, the process is spiral compression spring: rolling, de-stressed annealing, grinding of two ends, (shot blasting), (rectification), (de-stressed annealing), standing or strong pressure treatment, inspection, surface anti-corrosion treatment, packaging.Coil stretching spring: rolling, de-stress annealing, hook making, (cutting the tail), de-stress annealing, standing treatment, inspection, surface anti-corrosion treatment, packaging.Spiral torsion spring: rolling, de-stress annealing, torsion arm mak...
153
2018 - 11 - 02
Zinc electroplating: zinc is stable in dry air and changes little. A white film of zinc oxide or carbon zinc carbonate is formed in moist air. This dense film will prevent further corrosion. Therefore, the galvanizing layer is used for the spring corrosion protection under general atmospheric conditions. Zinc coating should not be used for all springs that are in contact with solutions such as sulfuric acid, hydrochloric acid and caustic soda, as well as springs that work in humid air such as sulfur trioxide.Generally, passivation of galvanized coating can improve the protective performance of...
NEW INFORMATION / More
136
2018 - 08 - 10
Stainless steel spring general precautions when washing, please pay attention to no surface friction to avoid the use of bleaching components and washing liquid containing abrasives, steel ball, grinding tools, etc., in order to remove the washing liquid, washing the end, rinse the surface with clean water.Surface state and washing methodDust and scaling - wash with soap or warm water.Label and film - scrub with warm water and weak detergent.Binder ingredients - use alcohol or organic solution;Fat, oil, lubricating oil contamination - with soft cloth or paper after drying with a neutral deterg...
137
2018 - 08 - 24
We can look at the relationship between the force applied to a spring and its resulting displacement. Again, there are three classes of springs: linear (or constant rate) springs, variable rate springs, and constant force springs.Linear springsLinear springs obey Hooke’s Law (F=k*x), which means that the force needed to extend or compress such a spring by distance x is proportional to the distance, as long as the force doesn’t exceed the elastic limit of the spring. Torsion springs obey an analogous version of Hooke’s Law (F=k*θ, where θ is an angle). In both cases, k is the spring rate, and i...
138
2018 - 09 - 08
(1) heat treatment technology for strengthening springs.1) protective atmosphere heat treatment. In our country, protective atmosphere heat treatment is adopted in spring, oil quenched and tempered steel wire and toughened steel whose wire rod is less than 15mm. Heat treatment in protective atmosphere can remove surface decarbonization and oxidation and improve the surface quality of materials.2) induction heating or protective atmosphere induction heating heat treatment. This process is usually carried out on the wire before forming the coil spring. Some spring factories combine heat treatmen...
139
2018 - 09 - 20
The purpose of mold spring is to take off material, press material, the strength of the spring, which is related to whether the mold production is smooth, whether the product is qualified.Spring force is small, may cause the product to be out of shape, the mold does not take off the material, the product is bad to take out from the mold inside, the belt material, the knife edge, punch easy to wear and so on each kind of question.Mold spring according to different production times, compression amount selected, the larger the spring life, the shorter die life, of course, the broken spring can be...
140
2018 - 09 - 30
Please avoid the improper way of using (1) more than the use of the maximum compression (300000 back to the conditions, after a close with the use of a long) stress causing the wreck, close to close with the use of a long, can make the spring line department gradually close to that, because of the high spring constant change caused by load curve with high, nearly and produce high stress to make spring break, please do not use more than 300000 times.The use of the spring without prepressure due to the gap caused the spring up and down vibration caused the spring distortion, if there is prepress...
141
2018 - 10 - 17
Washing method according to the surface state:General considerationsWhen washing, please pay attention not to scratch the surface to avoid using the bleaching ingredients and the cleaning solution containing abrasive agent, steel ball (brush roller ball), grinding tools, etc. In order to remove the cleaning solution, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and dirt are washed with soap, a mild detergent, or warm waterLabel and film with warm water, weak detergent to scrubThe binder ingredient is alcohol or organic solutionUse a mild clot...
142
2018 - 10 - 29
Each circle is formed into a tightly closed spiral ring or a pitch ring, which extends outwards when subjected to external forces and maintains a force of contraction towards the middle.There are many kinds of spring hooks: English hook, German hook, earring hook, fishtail hook, etc.(1) free length: (a) total length, (b) total length of the ring, and (c) length inside the hook ring.(2) control diameter :(a) outside diameter, (b) inside diameter, (c) inside diameter of casing.(3) steel wire size "wire diameter".(4) materials (type, grade).(5) winding number :(a) total winding number a...
143
2019 - 12 - 30
1、What is Passivation?As a post-fabrication method, passivation is intended to maximize the natural corrosion resistance of stainless steel. Stainless steel is a steel alloy that contains a minimum of 10.5% chromium content by mass and along with a number of other alloys. When stainless steel is newly formed it needs to be cleaned of lubricants, oils, greases and other substances used in its fabrication. Once the steel has been cleaned it must be passivated. Passivation is a process that treats metal surfaces with an acid solution to make the surface corrosion resistant.Passive to atmospheric ...
CONTACT US / More
hotline
86-755-28903526
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 126
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 136
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 78
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者:
发布时间: 2018 / 04 / 18
点击次数: 95
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens. Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms. Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
作者:
发布时间: 2018 / 04 / 18
点击次数: 112
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sacrificed to satisfy my curiosity. These days, I appreciate the grown-up applications of springs, especially when I drive over potholes on Highway!
作者:
发布时间: 2018 / 04 / 18
点击次数: 228
We do cherish the time together with all of our esteemed customers.  The picture shows the progressive hour withOne of our French customer who focus on the water purification system industry.
作者:
发布时间: 2018 / 04 / 18
点击次数: 159
To grow the business, we need to develop management expertise and innovation across the team.Thia is the picture of AFR team development activity in one of the shenzhen beach, From the faceof young team,  we can see the confidence and what they want to achieve!
作者:
发布时间: 2018 / 04 / 18
点击次数: 154
To develope the new customer and enhance the exist business relationship, we’ll be exhibiting at the 22th MechaniceComponents&Material Technology Expo(M-Tech) in Tokyo Japan from JUNE 20-23.  Your visiting at that timeIs highly welcomed!
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat