HOT INFORMATION / More
1
2018 - 04 - 18
To develope the new customer and enhance the exist business relationship, we’ll be exhibiting at the 22th MechaniceComponents&Material Technology Expo(M-Tech) in Tokyo Japan from JUNE 20-23.  Your visiting at that timeIs highly welcomed!
2
2018 - 07 - 26
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kin...
3
2018 - 08 - 08
The spring is often subjected to variable load or impact load. In order to ensure that the spring can work permanently and reliably, the material must have high elastic limit and fatigue limit. At the same time, it should have enough toughness and plasticity and good heat treatment.Spring materials and properties can be consulted in relevant manuals, specifications and standards (GB/T129.6-92, GB4357-89). The common spring steel is mainly:1: carbon spring steelThis kind of spring (such as 65, 70 steel, etc.) has the advantages of cheap price, convenient source of raw materials, low elastic lim...
4
2018 - 08 - 20
8.3.3 test machine should have the following functions: test time or preset function;Dynamic timing or counting function; test amplitude display or control function; automatic stop function.Evaluation of 8.4 spring fatigue test results8.4.1 fatigue life determination: under a given failure condition, the measured spring reachesThe maximum cycle number is the fatigue life of the spring.Verification of 8.4.2 fatigue life: if the number of cycles is tested, if the spring does not failThe validation test proved that the test was passed.8.4.3 reliability verification: according to the given reliabi...
5
2018 - 09 - 04
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount...
6
2018 - 09 - 17
Hard inspection method for chemical heat treatment and surface quenching and temperingSurface heat treatment is divided into two categories, one is chemical heat treatment and the other is surface quenching and tempering heat treatment. The hardness test method is as follows:1. Chemical heat treatmentChemical heat treatment is to make the workpiece surface infiltrate one or several chemical elements of the atom, thereby changing the workpiece surface chemical composition, organization and performance.After quenching and tempering, the surface of the workpiece has high hardness, wear resistance...
7
2018 - 09 - 27
In order to make it convenient for customers to buy and custom spring, some brief introduction about spring and specification parameters are summarized as follows:The common spring can be classified as: stretching spiral spring, compression spiral spring and torsion spiral spring.Among them, stretch and compression springs are mostly produced in quantity, with complicated specifications but suitable for slight modifications. If a small amount of springs is needed and the characteristics of springs are not critical, they can be purchased easily in the market with a higher unit price.The users o...
8
2018 - 10 - 12
There are many ways of making spring, but the main forming part is cold forming and hot forming.In spring in the cold forming process, the spring mainly made by oil material toughening, lead bath quenching tempering spring wire, cold drawn wire, etc., using this kind of material in the manufacturing process of spring generally do not need special heat treatment and only requires the stress relieving, adopted by the spring design work stress and material performance.Spring cold forming process is generally suitable for special-shaped spring with small line diameter or more complicated shape, su...
9
2018 - 10 - 23
Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of ela...
NEW INFORMATION / More
1
2018 - 04 - 18
To develope the new customer and enhance the exist business relationship, we’ll be exhibiting at the 22th MechaniceComponents&Material Technology Expo(M-Tech) in Tokyo Japan from JUNE 20-23.  Your visiting at that timeIs highly welcomed!
2
2018 - 08 - 02
Fr- spring radial load (N)  Radial stiffness of the F'r-spring (N/mm)  Fs- spring test load (N)  F- Spring deformation (mm)  Fj- deformation under working limit load Fj (mm)  Fr- spring static deformation (mm)  Fs- The amount of deformation of the spring under the test load Fs (mm); the amount of linear static deformation (mm)  Fo- tension spring corresponds to the assumed deformation amount (mm) of the tensile force Fo; the central deformation amount of the diaphragm (mm)  G-material shear modulus (MPa)  ...
3
2018 - 08 - 15
Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is...
4
2018 - 08 - 30
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compr...
5
2018 - 09 - 12
There are many methods of construction of paint, most of which are used for springs in the following ways:(1) dip coating method dip coating method is to dip the spring into the paint groove, and then take out, and let the excess paint on the surface drip naturally. After drying, it is covered with paint film on the surface of the spring.The dip-coating method has high production efficiency and can be applied to mechanization and automation production.But the paint volatilizes quickly, the paint that contains heavy quality pigment and two component paint material (amine solidify epoxy paint, p...
6
2018 - 09 - 25
Nowadays, with the development of science and technology, spring has become a very important hardware accessory in our life. Different products use different springs, and the longest used springs can be roughly divided into: pull spring, twist spring, press spring, disc spring and plate spring.The following features of a very practical tension spring:Many different products or hooks are used to guarantee the source of the tension of the tension spring. The tension spring works in the opposite way to the compression spring. The tension spring works in the opposite way when stretching or pulling...
7
2018 - 10 - 10
Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually ...
8
2018 - 10 - 20
After the end face grinding, if the free height, perpendicularity, pitch and outside diameter of the spring do not meet the deviation specified in the pattern, the screw compression spring often needs to be corrected.Calibration operations are generally manual or semi-manual.The commonly used tools are: the spring with the metal wire above 4mm, multi-purpose manual pressure machine, splitting machine, press and so on;For springs with wire under 4mm, special tools, pliers and hammers with wedge edge are often used.Calibration is to use these tools to make the spring locally plastic deformation ...
9
2018 - 11 - 02
Zinc electroplating: zinc is stable in dry air and changes little. A white film of zinc oxide or carbon zinc carbonate is formed in moist air. This dense film will prevent further corrosion. Therefore, the galvanizing layer is used for the spring corrosion protection under general atmospheric conditions. Zinc coating should not be used for all springs that are in contact with solutions such as sulfuric acid, hydrochloric acid and caustic soda, as well as springs that work in humid air such as sulfur trioxide.Generally, passivation of galvanized coating can improve the protective performance of...
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.

The basis of spring material selection

日期: 2018-10-20
浏览次数: 389
Daisy

1) the selection basis of environmental factors in the use state of spring products: corrosion resistance, acid corrosion resistance, alkali corrosion resistance, salt corrosion resistance, water corrosion resistance, etc.Weather resistance;Resistance to stress and corrosion, fatigue and corrosion, etc.Wear resistance;Temperature resistance, etc.Radiation resistance, etc.

2) selection basis of load characteristics of spring products: dynamic pulse-type cycle load, variable load, impact load, corrosion fatigue load, static load, large load and fatigue load, etc.

The basis of spring material selection

3) selection basis of mechanical properties and strength characteristics of spring products: tensile strength, yield strength or flexure ratio, hardness, thermal hardness, reduction of section, elongation, impact toughness, relaxation performance, fatigue strength, fracture toughness, etc.

4) the selection basis of physical characteristics of spring product materials mainly includes elastic modulus, density, conductivity, electromagnetic characteristics, heat transfer characteristics, etc.

5) the selection basis of material technological characteristics of spring products mainly includes: rolling processing, cutting performance, winding performance, torsion performance, bending performance, deformation strengthening, solid solution strengthening, precipitation strengthening, hardening, quenching, carbon removal performance, tempering performance, aging performance, welding performance, etc.

6) the selection basis of spring product shape features mainly includes: product section shape and size, dimension accuracy, bending degree, straightness, surface shape and roughness, planeness, etc.

7) the selection basis of the public safety features of spring products mainly includes: material toxicity, flammability, explosibility, volatility, pollution characteristics, etc


Relevant recommendations
2020 . 01 . 13
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant.   Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound into a plane of the spiral of a spring, the spring is fixed at one end, the other end of the material after acting torque bending torque, bending elastic deformation, so the spring in its own plane to p...
2020 . 01 . 13
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be noted that if critical force-versus-deflection linearity is required, only the center 60-80% of the available deflection range should be employed.Thus, reserve at least the first and last 15-20% of t...
2020 . 01 . 06
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension springs include carburetors, trampolines and farm machinery.Oil Tempered Spring WireOil tempered wire is cold drawn and heat treated before plating. Ideal as a general purpose spring wire, it is often us...
2020 . 01 . 06
springs are a mechanical part that use elasticity to work. Generally made of spring steel. It is widely used in machines and instruments to control the movement of machine parts, mitigate impact or vibration, store and store energy, measure force, etc.The spring is just an accumulator, it has the function of storing energy, but can not release the energy slowly, to achieve the release of this function should rely on the 'spring + large transmission ratio mechanism' to achieve, common in the mechanical table.The spring is widely used in the mechanical and electronic industry. The spring can produce a large elastic deformation under load and convert mechanical work or kinetic energy into deformation energy. After unloading, the spring's deformation disappears and returns to its original stat...
Related products / Products
  • 发布时间: 2018 - 04 - 08
    Precision Torsion Spring:Description: wire diameter ranged from Φ0.10-Φ14mm, minimum spring convolution: 3•Various materials: music wire,galvanised wire, carbon wire,stainless steel wire, copper, beryllium copper wire, and more•Various torsion arms•Single torsion, double torsion and multi-torsion•Torsion in different direction•Applications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic molds, sports equipment and gifts
  • 发布时间: 2018 - 04 - 08
    拉伸弹簧
    Precision Extension spring:Description: wire diameter ranged from Φ0.08-Φ14mm, minimum spring convolution: 2.7, hook style can be customized per customer’s requirement•Spring loops and hooks vary in different shapes•Changeable diameter•Advanced manufacturing and testing equipment•Made of standard material•Applications: furniture, electronic products, electric appliance, architecture, commodity and home appliance, sports equipment and gifts
  • 发布时间: 2018 - 04 - 08
    异形弹簧
    Auto wire forming Spring:Description: CNC forming, maximum feeding error:0.05mm,wire diameter ranged from 0.08-14mmAUTO Wire Formings and Clasps, Round, Flat and Square Wire Types are Available•Produced by specific clasp formers•Round wire, flat wire and square wire•Advanced manufacturing and testing equipment•Exported directly•Standard material•Responsive service•Applications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic moul...
  • 发布时间: 2018 - 04 - 08
    CD盖弹簧、电器按钮弹簧、剃须刀弹簧等…
    For household applicancedDescription: wire diameter ranged from Φ0.10-Φ14mm, minimum spring convolution: 3Various materials: music wire,galvanised wire, carbon wire,stainless steel wire, copper, beryllium copper wire, and moreVarious torsion armsSingle torsion, double torsion and multi-torsionTorsion in different directionApplications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic molds, sports equipment and gifts
  • 发布时间: 2018 - 04 - 20
    Bttery shell stamping parts
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat