HOT INFORMATION / More
1
2018 - 07 - 18
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
2
2018 - 08 - 01
The basic spring parameters of the spring:1. Spring wire diameter D: wire diameter of spring.2. The outer diameter of the spring D2: the maximum outer diameter of the spring.3. The inner diameter of the spring D1: the smallest outer diameter of the spring.4. The middle diameter of the spring is D: the average diameter of the spring. Their calculation formula is: D= (D2+D1) +2=D1+d=D2-d5, pitch T: except for the support ring, the distance between the two adjacent circles of the spring corresponds to the axial distance on the middle diameter of the spring, and is expressed by t.6, effective circ...
3
2018 - 08 - 15
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in...
4
2018 - 08 - 28
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
5
2018 - 09 - 11
Vibration damping spring is a common elastic component, which is widely used in various vibration equipment and automobile manufacturing industries. It has the advantages of good stability, low noise, good isolation effect and long service life.Compression springs, rubber springs, composite springs, air bag springs are vibration - reducing springs.Vibration damping spring can be divided into: wire compression spring, rubber spring, compound spring, rubber air spring, etc.Steel wire compression spring is a spiral spring under pressure, it USES the material section is mostly circular, also USES ...
6
2018 - 09 - 22
Spring is a kind of elastic element widely used in the mechanical and electronic industries. Spring can produce greater elastic deformation when loaded, and convert mechanical work or kinetic energy into deformation energy. After unloading, the deformation of spring disappears and returns to its original state, and the deformation energy is transformed into mechanical work or kinetic energy.The ratio of load and deformation of the spring is called spring stiffness.  There are many kinds of springs. They are used in various fields. According to the deformation condition, they can be divide...
7
2018 - 10 - 09
1. The standing treatment of the compression spring is to compress the spring to the working limit height or to tighten the height several times, usually 3 to 5 times;For the stretching spring, the length of the spring is drawn to the working limit several times;Torsion spring, is the spring in the working direction of the 5522 for the ultimate torsion Angle several times.2. Strong pressure (strong tension and strong torsion) treatment for compression spring is to press the spring into the material layer and the stress exceeds the yield point, resulting in negative residual stress on the surfa...
8
2018 - 10 - 19
1、 preparation before peening1) the size and surface roughness before spring-shot blasting should meet the requirements of the pattern, except for special instructions (if it is necessary to reprocess the shot blasting surface).2) the spring shall complete the prescribed heat treatment before shot peening.3) the non-destructive test of the spring shall be completed before the shot peening treatment, or after the shot peening if there is special requirement.4) the surface of the spring to be sprayed should be clean, dry and free of oil.2、 treatment after shot peening1) the heating temperature o...
9
2018 - 11 - 02
Cylindrical spiral spring structureThere are three types of cylindrical spiral spring:1. Cylindrical spiral compression spring1) spacing between springsLet the spring's pitch be p;The diameter of the spring wire is d;In the free state, there should be proper spacing between the circles.In order to make the spring still maintain a certain elasticity after compression, it is also necessary to ensure that there is a certain gap of 1 between each circle under the maximum load.The size of lens 1 is generally recommended to be: in addition 1=0.1d or greater than 0.2mm2) dead circleThe two ends o...
NEW INFORMATION / More
1
2018 - 07 - 30
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30...
2
2018 - 08 - 10
Stainless steel spring general precautions when washing, please pay attention to no surface friction to avoid the use of bleaching components and washing liquid containing abrasives, steel ball, grinding tools, etc., in order to remove the washing liquid, washing the end, rinse the surface with clean water.Surface state and washing methodDust and scaling - wash with soap or warm water.Label and film - scrub with warm water and weak detergent.Binder ingredients - use alcohol or organic solution;Fat, oil, lubricating oil contamination - with soft cloth or paper after drying with a neutral deterg...
3
2018 - 08 - 24
We can look at the relationship between the force applied to a spring and its resulting displacement. Again, there are three classes of springs: linear (or constant rate) springs, variable rate springs, and constant force springs.Linear springsLinear springs obey Hooke’s Law (F=k*x), which means that the force needed to extend or compress such a spring by distance x is proportional to the distance, as long as the force doesn’t exceed the elastic limit of the spring. Torsion springs obey an analogous version of Hooke’s Law (F=k*θ, where θ is an angle). In both cases, k is the spring rate, and i...
4
2018 - 09 - 08
(1) heat treatment technology for strengthening springs.1) protective atmosphere heat treatment. In our country, protective atmosphere heat treatment is adopted in spring, oil quenched and tempered steel wire and toughened steel whose wire rod is less than 15mm. Heat treatment in protective atmosphere can remove surface decarbonization and oxidation and improve the surface quality of materials.2) induction heating or protective atmosphere induction heating heat treatment. This process is usually carried out on the wire before forming the coil spring. Some spring factories combine heat treatmen...
5
2018 - 09 - 20
The purpose of mold spring is to take off material, press material, the strength of the spring, which is related to whether the mold production is smooth, whether the product is qualified.Spring force is small, may cause the product to be out of shape, the mold does not take off the material, the product is bad to take out from the mold inside, the belt material, the knife edge, punch easy to wear and so on each kind of question.Mold spring according to different production times, compression amount selected, the larger the spring life, the shorter die life, of course, the broken spring can be...
6
2018 - 09 - 30
Please avoid the improper way of using (1) more than the use of the maximum compression (300000 back to the conditions, after a close with the use of a long) stress causing the wreck, close to close with the use of a long, can make the spring line department gradually close to that, because of the high spring constant change caused by load curve with high, nearly and produce high stress to make spring break, please do not use more than 300000 times.The use of the spring without prepressure due to the gap caused the spring up and down vibration caused the spring distortion, if there is prepress...
7
2018 - 10 - 17
Washing method according to the surface state:General considerationsWhen washing, please pay attention not to scratch the surface to avoid using the bleaching ingredients and the cleaning solution containing abrasive agent, steel ball (brush roller ball), grinding tools, etc. In order to remove the cleaning solution, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and dirt are washed with soap, a mild detergent, or warm waterLabel and film with warm water, weak detergent to scrubThe binder ingredient is alcohol or organic solutionUse a mild clot...
8
2018 - 10 - 29
Each circle is formed into a tightly closed spiral ring or a pitch ring, which extends outwards when subjected to external forces and maintains a force of contraction towards the middle.There are many kinds of spring hooks: English hook, German hook, earring hook, fishtail hook, etc.(1) free length: (a) total length, (b) total length of the ring, and (c) length inside the hook ring.(2) control diameter :(a) outside diameter, (b) inside diameter, (c) inside diameter of casing.(3) steel wire size "wire diameter".(4) materials (type, grade).(5) winding number :(a) total winding number a...
9
2019 - 12 - 30
1、What is Passivation?As a post-fabrication method, passivation is intended to maximize the natural corrosion resistance of stainless steel. Stainless steel is a steel alloy that contains a minimum of 10.5% chromium content by mass and along with a number of other alloys. When stainless steel is newly formed it needs to be cleaned of lubricants, oils, greases and other substances used in its fabrication. Once the steel has been cleaned it must be passivated. Passivation is a process that treats metal surfaces with an acid solution to make the surface corrosion resistant.Passive to atmospheric ...
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.

Inspection content and specification for spring parts(part 3)

日期: 2018-08-16
浏览次数: 222
nelson

6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.

The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.

6.1.11 spring straightness detection: put the spring level on the plate and roll one.

Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.

The measured gap is the deviation of the straightness.

Measurement of geometry size of 6.2 stretch spring

The dimension of tensile spring is roughly measured: material diameter, free length and spring.

The diameter, total number of rings, the relative angle of two hook rings, the position of the central surface of the hook ring, the position of the spring center line, the length of the spring hook ring part, etc. The detection of the first 4 items is based on the compression spring detection method. The following are mainly introduced the following several detection methods.

Inspection content and specification for spring parts(part 3)

6.2.1 spring two hook ring relative angle detection: stretching spring two hook ring relative angle

The detection method is to place the spring level on the flat plate, including the end hook torus and the wide seat angle. The angle gauge is used to measure the angle a of the hook torus and the flat plate on the other end of the spring, and the relative angle tolerance of the two hook and ring is =a -90 degrees.

The position of 6.2.2 spring clasp center and axis line: the center and the shell of the hook ring of the pull spring.

The position tolerance of the spring axis is measured with a depth gauge or a special template. First, the spring is placed in the V slot, and the height of the hook and ring plane is measured. Then 180 degrees are turned over and the height of the other side is measured. The one to half of the difference of the two measurement values is the deviation of the position degree. When there is no suitable V groove, the spring can be placed on the flat plate for measuring.

Inspection content and specification for spring parts(part 3)

6.2.3 spring hook ring length detection: check with vernier caliper.

6.2.4 total number of springs detection: the total number of cycles as a reference value, when the hook position requirements, should ensure the location of the hook ring. The detection method is visual.

Detection of geometry size of 6.3 torsion spring

The measuring contents of the torsion spring geometry include material diameter, free length, free angle, spring diameter, total circle number, twist arm length, twist arm bending angle and so on.

6.3.1 spring free length detection: the free length of the ring spring is not examined. The detection method refers to the compression spring.

6.3.2 spring free angle detection:

The springs with characteristic requirements are not allowed to be examined at a free angle.

The angle of spring can be measured by angle gauge, tool microscope or special measuring tool.

The way to detect the free angle of the angle gauge is to adjust the angle of the angle gauge to coincide with the arms.

The angle of the clip is the free angle of the spring.

6.3.3 spring torsion arm length measurement: check with vernier depth gauge or vernier caliper.

6.3.4 spring torsion arm detection: reference spring free angle detection.

6.3.5 torsion spring diameter, material diameter and total circle number are checked with reference to compression springs.

The detection method is carried out.


Relevant recommendations
2020 . 01 . 13
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant.   Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound into a plane of the spiral of a spring, the spring is fixed at one end, the other end of the material after acting torque bending torque, bending elastic deformation, so the spring in its own plane to p...
2020 . 01 . 13
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be noted that if critical force-versus-deflection linearity is required, only the center 60-80% of the available deflection range should be employed.Thus, reserve at least the first and last 15-20% of t...
2020 . 01 . 06
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension springs include carburetors, trampolines and farm machinery.Oil Tempered Spring WireOil tempered wire is cold drawn and heat treated before plating. Ideal as a general purpose spring wire, it is often us...
2020 . 01 . 06
springs are a mechanical part that use elasticity to work. Generally made of spring steel. It is widely used in machines and instruments to control the movement of machine parts, mitigate impact or vibration, store and store energy, measure force, etc.The spring is just an accumulator, it has the function of storing energy, but can not release the energy slowly, to achieve the release of this function should rely on the 'spring + large transmission ratio mechanism' to achieve, common in the mechanical table.The spring is widely used in the mechanical and electronic industry. The spring can produce a large elastic deformation under load and convert mechanical work or kinetic energy into deformation energy. After unloading, the spring's deformation disappears and returns to its o...
Related products / Products
  • 发布时间: 2018 - 04 - 08
    Precision Torsion Spring:Description: wire diameter ranged from Φ0.10-Φ14mm, minimum spring convolution: 3•Various materials: music wire,galvanised wire, carbon wire,stainless steel wire, copper, beryllium copper wire, and more•Various torsion arms•Single torsion, double torsion and multi-torsion•Torsion in different direction•Applications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic molds, sports equipment and gifts
  • 发布时间: 2018 - 04 - 08
    拉伸弹簧
    Precision Extension spring:Description: wire diameter ranged from Φ0.08-Φ14mm, minimum spring convolution: 2.7, hook style can be customized per customer’s requirement•Spring loops and hooks vary in different shapes•Changeable diameter•Advanced manufacturing and testing equipment•Made of standard material•Applications: furniture, electronic products, electric appliance, architecture, commodity and home appliance, sports equipment and gifts
  • 发布时间: 2018 - 04 - 08
    异形弹簧
    Auto wire forming Spring:Description: CNC forming, maximum feeding error:0.05mm,wire diameter ranged from 0.08-14mmAUTO Wire Formings and Clasps, Round, Flat and Square Wire Types are Available•Produced by specific clasp formers•Round wire, flat wire and square wire•Advanced manufacturing and testing equipment•Exported directly•Standard material•Responsive service•Applications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic moul...
  • 发布时间: 2018 - 04 - 08
    CD盖弹簧、电器按钮弹簧、剃须刀弹簧等…
    For household applicancedDescription: wire diameter ranged from Φ0.10-Φ14mm, minimum spring convolution: 3Various materials: music wire,galvanised wire, carbon wire,stainless steel wire, copper, beryllium copper wire, and moreVarious torsion armsSingle torsion, double torsion and multi-torsionTorsion in different directionApplications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic molds, sports equipment and gifts
  • 发布时间: 2018 - 04 - 20
    Bttery shell stamping parts
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat