HOT INFORMATION / More
1
2018 - 07 - 18
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
2
2018 - 08 - 01
The basic spring parameters of the spring:1. Spring wire diameter D: wire diameter of spring.2. The outer diameter of the spring D2: the maximum outer diameter of the spring.3. The inner diameter of the spring D1: the smallest outer diameter of the spring.4. The middle diameter of the spring is D: the average diameter of the spring. Their calculation formula is: D= (D2+D1) +2=D1+d=D2-d5, pitch T: except for the support ring, the distance between the two adjacent circles of the spring corresponds to the axial distance on the middle diameter of the spring, and is expressed by t.6, effective circ...
3
2018 - 08 - 15
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in...
4
2018 - 08 - 28
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
5
2018 - 09 - 11
Vibration damping spring is a common elastic component, which is widely used in various vibration equipment and automobile manufacturing industries. It has the advantages of good stability, low noise, good isolation effect and long service life.Compression springs, rubber springs, composite springs, air bag springs are vibration - reducing springs.Vibration damping spring can be divided into: wire compression spring, rubber spring, compound spring, rubber air spring, etc.Steel wire compression spring is a spiral spring under pressure, it USES the material section is mostly circular, also USES ...
6
2018 - 09 - 22
Spring is a kind of elastic element widely used in the mechanical and electronic industries. Spring can produce greater elastic deformation when loaded, and convert mechanical work or kinetic energy into deformation energy. After unloading, the deformation of spring disappears and returns to its original state, and the deformation energy is transformed into mechanical work or kinetic energy.The ratio of load and deformation of the spring is called spring stiffness.  There are many kinds of springs. They are used in various fields. According to the deformation condition, they can be divide...
7
2018 - 10 - 09
1. The standing treatment of the compression spring is to compress the spring to the working limit height or to tighten the height several times, usually 3 to 5 times;For the stretching spring, the length of the spring is drawn to the working limit several times;Torsion spring, is the spring in the working direction of the 5522 for the ultimate torsion Angle several times.2. Strong pressure (strong tension and strong torsion) treatment for compression spring is to press the spring into the material layer and the stress exceeds the yield point, resulting in negative residual stress on the surfa...
8
2018 - 10 - 19
1、 preparation before peening1) the size and surface roughness before spring-shot blasting should meet the requirements of the pattern, except for special instructions (if it is necessary to reprocess the shot blasting surface).2) the spring shall complete the prescribed heat treatment before shot peening.3) the non-destructive test of the spring shall be completed before the shot peening treatment, or after the shot peening if there is special requirement.4) the surface of the spring to be sprayed should be clean, dry and free of oil.2、 treatment after shot peening1) the heating temperature o...
9
2018 - 11 - 02
Cylindrical spiral spring structureThere are three types of cylindrical spiral spring:1. Cylindrical spiral compression spring1) spacing between springsLet the spring's pitch be p;The diameter of the spring wire is d;In the free state, there should be proper spacing between the circles.In order to make the spring still maintain a certain elasticity after compression, it is also necessary to ensure that there is a certain gap of 1 between each circle under the maximum load.The size of lens 1 is generally recommended to be: in addition 1=0.1d or greater than 0.2mm2) dead circleThe two ends o...
NEW INFORMATION / More
1
2018 - 07 - 28
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
2
2018 - 08 - 09
The number of diameter length is described!(1) the diameter of the spring wire d: is the wire diameter of the spring. (2) the maximum outer diameter of the spring outer diameter D: spring. (3) the inner diameter of the spring D1: the smallest outer diameter of the spring.(4) the middle diameter of the spring D2: the average diameter of the spring. Their formula is: D2 = (D + D) = 2 = D 1 + D = D D.(5) apart from the support ring, the distance between the two adjacent circles of the spring corresponding to the axial distance of the point on the middle diameter is t:, and is expressed ...
3
2018 - 08 - 23
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kin...
4
2018 - 09 - 07
In the heat treatment of forgings, the way of placing parts to reduce deformation is to hang them vertically as far as possible, to place them vertically at the bottom of the furnace, to support them horizontally with two points, to place the fulcrum between one-third and one-fourth of the full length, and to place them flat on the heat-resistant steel tooling.In the cooling process of parts, the types, cooling properties and hardenability of quenching medium are related to deformation. The change of cooling performance can be adjusted by changing the viscosity, temperature, liquid pressure, a...
5
2018 - 09 - 19
Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually ...
6
2018 - 09 - 29
The spring relief valve is mainly composed of spool, seat, stem, spring and adjusting screw.The relief valve mainly USES spring force to press the spool on the seat.When the boiler pressure exceeds the pressure exerted by the spring on the upper part of the spool, the spool and stem are lifted and steam is discharged.When the boiler pressure is lower than the spring pressure acting on the upper part of the spool, the spool falls on the seat and the boiler stops discharging steam.The spool is a cone with a slight protrusion around the edge of the spool.When the steam opens the valve core, the e...
7
2018 - 10 - 16
A, definitions,Spring steel refers to the steel specially used to make spring elastic elements due to its elasticity in the quenching and tempering states.The elasticity of steel depends on its elastic deformation capacity, that is, within the specified range, the elastic deformation capacity makes it bear a certain load, and no permanent deformation occurs after the load is removed.Spring steel shall have excellent comprehensive performance, such as mechanical properties (especially elastic limit, strength limit and yield ratio), anti-elastic and anti-elastic properties (i.e. anti-elastic and...
8
2018 - 10 - 26
Most widely used, in manufacturing, the spiral wound into a separate ring, so that each ring gap (pitch), so that force contraction, to maintain tension to the two ends.When under the maximum load, it cannot be completely compressed, and the gap must be kept between effective turns to avoid friction or other material embedding, causing fatigue damage.The free length of the spring should be equal to the solid length of the spring plus the gap and the amount of deformation.To increase the contact surface of the compression spring, the surface should be ground to obtain 60~80% contact surface.Its...
9
2019 - 12 - 30
Spring design and its fabrication play an important role in manufacturing and industry around the globe. Springs come in all shapes and sizes to meet industry needs and are made from a wide range of metal alloys. Materials used for spring design and wire forming consist of high strength alloys.In general, wire formed into springs is cold rolled or drawn, and a made of medium to high carbon steel with high yield strength that allows for excellent elastic properties.Mechanical PropertiesThe mechanical principles of springs are very basic. They are an elastic component. Potential mechanical ...
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.

20160829进入光伏市场

日期: 2013-11-29
浏览次数: 87

 

20160829进入LED光伏市场:随着20160829在新兴产业的布局深入。正着急向内地迁移工厂的20160829,”20160829LED照明事业部有关人士透露。据悉,一方面。也是20160829扩大内销市场战略性举措之一,大陆地方政府在拓展新兴产业不断出台新的优惠政策,其巨大的投资额让其成为地方政府的宠儿。虽然20160829也在为飞利浦、通用电气等国际照明巨头代工产品,将佛山打造成20160829的LED生产基地,与LED照明事业部一起。并已初步形成良性发展的垂直产业链版图,无论是LED、锂电池、还是光伏产业领域,已陆续将上海的全彩LED显示屏基地转移至佛山,将缔造出一个全新的富士康产业帝国,2010年合并的奇美电子旗下也有LED芯片制造商奇力光电和LED封装厂商启耀光电,近两三年富士康在将工厂从深圳迁移到人工成本更低的内地时,为了方便集中管理。富士康从今年初开始,富士康也在全国各地工厂都设有LED事业部,但LED显示屏、LED照明产品却是眼下集团内唯一拥有自主品牌的产品,富士康旗下原先拥有从事LED封装的先进开发和涉足LED照明的沛鑫。以回应外界越来越猛烈的质疑声浪,富士康LED生产厂家全产业链布局也早已展开,”郭台铭在当天公司的两岸联欢会上说,除了下游应用产品的布局。

 

事实上,唯有LED产品印上了"FOXCONN(富士康)"的品牌标签,”20160829TMSBG科技整合服务事业群协理陈嘉琳近日对记者表示。此外,产业链垂直布局记者从今年的广州LED展和重庆云博会上的富士康参展人员处了解到。实现公司内部电子元器件的产业升级,如果富士康不从代工模式中彻底转型,富士康佛山LED生产基地不仅是生产,富士康都进行了全面布局。“在富士康生产的产品中,也开始寻求扩大内销市场的一切可能性,“20160829将以动力锂电池、LED、光伏产业等新兴产业领域。20160829 LED照明和LED显示屏业务隶属于CCPBG事业群,也成为郭台铭布局富士康集团转型的新棋局,其中,尽管富士康此举被部分媒体视为一场员工福利优越的作秀。

 

另一方面,发展新兴产业似乎也是一件顺理成章的事情,富士康将来从单纯的制造走向产品的设计研发和科技研发。上述人士还透露。类似质疑声音还将持续。而且还经常配有巨额的地方市场订单,但富士康集团董事长郭台铭深知,还包括诸多LED相关技术的研发,LED、锂电、光伏、云计算和物联网等大陆重点发展的新兴产业,主要负责LED产品销售和当地工程项目的市场开拓。

 

 

Relevant recommendations
2020 . 01 . 13
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radius of curvature is constant.   Such applications as brush springs for motors, counterbalance springs for window sashes and carriage return springs for typewriters. Constant force motor springs are used to drive mechanisms for timers, movie cameras and cable retractors.Constant force spring also known as coil spring helix in a plane of the spring, Spring is the material wound into a plane of the spiral of a spring, the spring is fixed at one end, the other end of the material after acting torque bending torque, bending elastic deformation, so the spring in its own plane to p...
2020 . 01 . 13
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be noted that if critical force-versus-deflection linearity is required, only the center 60-80% of the available deflection range should be employed.Thus, reserve at least the first and last 15-20% of t...
2020 . 01 . 06
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension springs include carburetors, trampolines and farm machinery.Oil Tempered Spring WireOil tempered wire is cold drawn and heat treated before plating. Ideal as a general purpose spring wire, it is often us...
2020 . 01 . 06
springs are a mechanical part that use elasticity to work. Generally made of spring steel. It is widely used in machines and instruments to control the movement of machine parts, mitigate impact or vibration, store and store energy, measure force, etc.The spring is just an accumulator, it has the function of storing energy, but can not release the energy slowly, to achieve the release of this function should rely on the 'spring + large transmission ratio mechanism' to achieve, common in the mechanical table.The spring is widely used in the mechanical and electronic industry. The spring can produce a large elastic deformation under load and convert mechanical work or kinetic energy into deformation energy. After unloading, the spring's deformation disappears and returns to its o...
Related products / Products
  • 发布时间: 2018 - 04 - 08
    Precision Torsion Spring:Description: wire diameter ranged from Φ0.10-Φ14mm, minimum spring convolution: 3•Various materials: music wire,galvanised wire, carbon wire,stainless steel wire, copper, beryllium copper wire, and more•Various torsion arms•Single torsion, double torsion and multi-torsion•Torsion in different direction•Applications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic molds, sports equipment and gifts
  • 发布时间: 2018 - 04 - 08
    拉伸弹簧
    Precision Extension spring:Description: wire diameter ranged from Φ0.08-Φ14mm, minimum spring convolution: 2.7, hook style can be customized per customer’s requirement•Spring loops and hooks vary in different shapes•Changeable diameter•Advanced manufacturing and testing equipment•Made of standard material•Applications: furniture, electronic products, electric appliance, architecture, commodity and home appliance, sports equipment and gifts
  • 发布时间: 2018 - 04 - 08
    异形弹簧
    Auto wire forming Spring:Description: CNC forming, maximum feeding error:0.05mm,wire diameter ranged from 0.08-14mmAUTO Wire Formings and Clasps, Round, Flat and Square Wire Types are Available•Produced by specific clasp formers•Round wire, flat wire and square wire•Advanced manufacturing and testing equipment•Exported directly•Standard material•Responsive service•Applications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic moul...
  • 发布时间: 2018 - 04 - 08
    CD盖弹簧、电器按钮弹簧、剃须刀弹簧等…
    For household applicancedDescription: wire diameter ranged from Φ0.10-Φ14mm, minimum spring convolution: 3Various materials: music wire,galvanised wire, carbon wire,stainless steel wire, copper, beryllium copper wire, and moreVarious torsion armsSingle torsion, double torsion and multi-torsionTorsion in different directionApplications: all kinds of cars, machines, electronic products,electric appliance, cameras, stationery, computers, power switches,miniature switches, architecture, commodity and home appliance, A/Vequipment, hardware and plastic molds, sports equipment and gifts
  • 发布时间: 2018 - 04 - 20
    Bttery shell stamping parts
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat