HOT INFORMATION
<
  • 2018 . 10 . 17
    263
    Daisy
    Washing method according to the surface state:General considerationsWhen washing, please pay attention not to scratch the surface to avoid using the bleaching ingredients and the cleaning solution containing abrasive agent, steel ball (brush roller ball), grinding tools, etc. In order to remove the cleaning solution, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and dirt are washed with soap, a mild detergent, or warm waterLabel and film with warm water, weak detergent to scrubThe binder ingredient is alcohol or organic solutionUse a mild cloth or paper to dry and then wash with a neutral detergent or an ammonia solution or a special detergentRinse immediately with water, soak in an aqueous solution of ammonia or neutral carbonated soda, a...
  • 2018 . 10 . 16
    257
    Daisy
    A, definitions,Spring steel refers to the steel specially used to make spring elastic elements due to its elasticity in the quenching and tempering states.The elasticity of steel depends on its elastic deformation capacity, that is, within the specified range, the elastic deformation capacity makes it bear a certain load, and no permanent deformation occurs after the load is removed.Spring steel shall have excellent comprehensive performance, such as mechanical properties (especially elastic limit, strength limit and yield ratio), anti-elastic and anti-elastic properties (i.e. anti-elastic and anti-loose properties), fatigue properties, quenching properties, physical and chemical properties (heat resistance, low temperature resistance, oxidation resistance, corrosion resistance, etc.).In o...
  • 2018 . 10 . 16
    254
    Daisy
    The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension springs, should be preferentially used steel wire, cold-drawn steel wire such as strengthened steel wire, lead bath and oil hardened tempered steel wire, which has higher strength and good surface qua...
  • 2018 . 10 . 15
    284
    Daisy
    There are three ways to use stainless steel spring to remove oil and oxide skin:1. Immerse the stainless steel spring into the plastic container with the metal cleaning agent A diluted with water (the proportion of cleaning agent A and water dilution is 1:1 or 1:2), and the time should be as follows: the spring surface should be free from oil and oxide skin to restore the metal color. The soaking time should not be too long.So stainless steel spring surface has matte effect.2. In the ultrasonic equipment, the proportion of cleaning agent and water is about 1:30. It is advisable to restore the metal color without oil and oxide skin on the spring surface.The above two methods can be applied to high precision spring.3. After the cleaning agent A is put into the vibration polishing machine wit...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology

News NEWS INFORMATION
HOT INFORMATION / More
82
2018 - 09 - 28
The diameter of wire wound by automatic spring machine is 0.2-3mm, and the adjustment process is as follows:1. Calibrate the feeding roller and winch to fit the diameter of steel wire and install the pitch wedge and cutting knife.2. Insert the steel wire into the spring machine and press the pressure plate and feeding roller.3. Adjust the distance of winding xiao zi, control the diameter of spring, and adjust the pitch wedge and xiao zi Angle to control the spring pitch and parallel head.4. Install an appropriate cutter, adjust the feeding CAM according to the spring expansion length, cut off ...
83
2018 - 07 - 24
(5) the development of spring steel wireAfter more than 100 years of development, the technology of spring steel has experienced lead hardened to oil quenching, and now it develops to induction hardening. Coupled with the continuous innovation and improvement of technology and equipment, the quality of varieties is constantly updated. The newly developed valves have been developed by induction heating and tempering with spring steel wire. It has been proved that the plastic, toughness, relaxation, fracture toughness, delayed fracture resistance, fatigue life and so on are all compared with oil...
84
2018 - 09 - 13
The surface of steel is hardenedIn some parts, the surface layer of the workpiece bears higher stress than the core under the action of alternating loads such as torsion and bending and impact loads.In the case of friction, the surface layer is also constantly worn. Therefore, high strength, high hardness, high wear resistance and high fatigue limit are put forward for some surface layer of parts. Only surface strengthening can meet the above requirements.Because surface quenching has the advantages of small deformation and high productivity, it is widely used in production.According to differ...
85
2018 - 11 - 03
Internal combustion engine valve spring, low, medium and high stress valve spring, safety valve spring, pressure reducing valve, electric regulating valve, pneumatic regulating valve, self-support regulating valve, hydraulic control valve, steam trap, gate valve, as per valve, butterfly valve, ball valve, check valve, special valve, hydraulic valve, electromagnetic valve, etc.Relief valve: spring safety valve by using the spring force, spring loaded relief valve is closed and not closed in two kinds of structure, general inflammable, explosive or toxic medium should choose enclosed, steam or i...
86
2018 - 08 - 25
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of ...
87
2018 - 10 - 18
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle ...
88
2018 - 08 - 09
At first, during the experiment, Hooke found that the weight added to the spring was proportional to the elongation of the spring, and he tested his conjectures by many experiments. In 1678, Hooke wrote a spring paper, which introduced the results of experiments on elastic objects, laying the foundation for the development of material mechanics and elastic mechanics.Spring dynamometerIn the early nineteenth Century, under the premise of a lot of experimental work in the former, British scientist Thomas Yang summed up the research results of Hooke and others, pointing out that if the elongation...
89
2018 - 09 - 28
The special-shaped spring contains spring clip, tension spring and torsion spring, and the generalized special-shaped spring also includes snake spring, corrugated spring, bar spring and other complicated springs.Special-shaped spring is the basic part with wide application range and multifarious variety in automobile, motorcycle, electric appliance and instrument products. Its quality and life directly affect the performance of main engine products.Hyundai has made it a key component.Over 90% of special-shaped springs at home and abroad are made of two kinds of materials: lead quenched carbon...
90
2018 - 07 - 24
Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of ela...
NEW INFORMATION / More
82
2020 - 01 - 06
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless Steel SpringsStainless steel springs have low-stress relaxation and resist corrosion. They have good strength at moderate temperatures and are resistant to heat. Extension springs are most commonly made from stainless steel.Extension springs absorb energy and provide resistance to pulling. As the name suggests, an extension spring stretches as a load is applied to it. Applications for extension spr...
83
2018 - 09 - 06
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
84
2018 - 10 - 25
The spring relief valve is mainly composed of spool, seat, stem, spring and adjusting screw.The relief valve mainly USES spring force to press the spool on the seat.When the boiler pressure exceeds the pressure exerted by the spring on the upper part of the spool, the spool and stem are lifted and steam is discharged.When the boiler pressure is lower than the spring pressure acting on the upper part of the spool, the spool falls on the seat and the boiler stops discharging steam.The spool is a cone with a slight protrusion around the edge of the spool.When the steam opens the valve core, the e...
85
2018 - 08 - 16
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30...
86
2018 - 10 - 11
Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat ...
87
2018 - 07 - 31
8.3.3 test machine should have the following functions: test time or preset function;Dynamic timing or counting function; test amplitude display or control function; automatic stop function.Evaluation of 8.4 spring fatigue test results8.4.1 fatigue life determination: under a given failure condition, the measured spring reachesThe maximum cycle number is the fatigue life of the spring.Verification of 8.4.2 fatigue life: if the number of cycles is tested, if the spring does not failThe validation test proved that the test was passed.8.4.3 reliability verification: according to the given reliabi...
88
2018 - 09 - 21
compression spring is under axial pressure of the spiral spring, it is used in the data section for more rounded, useful also rectangle and multi-strand steel rolled a travelling, spring is usually pitch, such as the shape of the compression spring are: cylindrical, conical, convex and concave and a small amount of noncircular, compression spring there is a certain gap between circle and circle, when under external load spring contraction deformation, deformation energy storage.The tension spring is a spiral spring that bears the axial tension.When there is no load, the stretch spring is usual...
89
2020 - 01 - 13
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be...
90
2018 - 09 - 07
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount...
CONTACT US / More
hotline
86-755-28903526
Room 816, RongChao Financial Center, No 52, RuYi Road,LongCheng Street, LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 0
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 0
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 1
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者: nelson
发布时间: 2018 / 09 / 11
点击次数: 6
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of piano ste...
作者: Daisy
发布时间: 2018 / 09 / 10
点击次数: 13
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which is a chemical corrosion.If the spring is in contact with the electrolyte solution, the corrosion caused by the action of the micro battery is called electrochemical corrosion.For example, the spring is...
作者: nelson
发布时间: 2018 / 09 / 10
点击次数: 20
Spring grinding is easy to produce cracks at the end of the tightness, and directly affect the verticality of the spring, load and free length size, so the general grinding process of spring should be carried out after stress relief tempering. Eliminate the residual stress of steel wire cold drawing to prevent the generation of end gap cracks.The main factors that affect the quality of springs in grinding are as follows:(1) The grinding wheel should be selected reasonably; (2) the control of the bevel angle of the end ring; (3) a certain number of special measuring tools should be equipped to ensure the grinding quality; (4) the grinding wheel should be repaired in time; (5) the correct size of the grinding sleeve should be selected, and the gap between the spring and the sleeve should be ...
作者: nelson
发布时间: 2018 / 09 / 08
点击次数: 21
(1) heat treatment technology for strengthening springs.1) protective atmosphere heat treatment. In our country, protective atmosphere heat treatment is adopted in spring, oil quenched and tempered steel wire and toughened steel whose wire rod is less than 15mm. Heat treatment in protective atmosphere can remove surface decarbonization and oxidation and improve the surface quality of materials.2) induction heating or protective atmosphere induction heating heat treatment. This process is usually carried out on the wire before forming the coil spring. Some spring factories combine heat treatment of wire materials with spring making to reduce costs. Induction heating treatment has better strengthening effect, rapid induction heating speed, help to refine grain and reduce surface decarbonizat...
作者: nelson
发布时间: 2018 / 09 / 07
点击次数: 10
In the heat treatment of forgings, the way of placing parts to reduce deformation is to hang them vertically as far as possible, to place them vertically at the bottom of the furnace, to support them horizontally with two points, to place the fulcrum between one-third and one-fourth of the full length, and to place them flat on the heat-resistant steel tooling.In the cooling process of parts, the types, cooling properties and hardenability of quenching medium are related to deformation. The change of cooling performance can be adjusted by changing the viscosity, temperature, liquid pressure, additives and stirring of the medium. The higher the viscosity of quenching oil, the higher the temperature, the smaller the elliptical deformation. In static state, the deformation is small.The follow...
作者: nelson
发布时间: 2018 / 09 / 07
点击次数: 8
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount of shrinkage is directly proportional to the supersaturated carbon content. When heated at room temperature of -200, part of austenite is transformed into martensite and expanded. However, the expans...
作者: nelson
发布时间: 2018 / 09 / 06
点击次数: 15
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spring process has to be cut off, a spring connected to several springs is separated into a single spring.Some important springs can add a blank height classification procedure before grinding the face t...
作者: nelson
发布时间: 2018 / 09 / 05
点击次数: 16
1, matching springs and springs based on automobiles, motorcycles, diesel engines and gasoline engines. This type of spring has valve spring, suspension spring, damping spring and clutch spring, etc., with a large amount, which accounts for about 50% of the spring production. At the same time, the technical level is also high, it can be said that the technical level of these springs is representative, they are mainly to the high fatigue life and high anti relaxation direction, thus reducing the quality. 2. Large springs and plate springs, which mainly include railway rolling stock, heavy truck and engineering machinery, are mainly formed by hot coil forming, which is an important aspect of the spring manufacturing industry. With the development of high-speed railway and the upgrading ...
作者: nelson
发布时间: 2018 / 09 / 04
点击次数: 14
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount of shrinkage is directly proportional to the supersaturated carbon content. When heated at room temperature of -200, part of austenite is transformed into martensite and expanded. However, the expans...
158页次10/18首页PrePage...  567891011121314...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat