HOT INFORMATION
<
  • Method for improving heat treatment performance
    Method for improving heat treatment performance
    2018 . 10 . 11
    409
    Daisy
    Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat treatment furnace design matches the design of the expert process control system.Eurotherm already has a unique knowledge of aviation and automotive heat treatment specifications.These knowledge and s...
    more
  • The finish of the spring surface
    The finish of the spring surface
    2018 . 10 . 10
    300
    Daisy
    In recent years, the surface of the spring has been treated by the spring designers.The finishing (finishing) process is to put the spring directly into a series of finishing machines, such as tilting centrifugal type or spiral vibrating type, eddy current type, and add appropriate grinding materials, grinding agents and water for finishing.General optical finishing is about 20 to 30min. Specific optical finishing time depends on the spring shape and the amount of device.After finishing the finish, remove the spring and rinse it with tap water, then immerse in the SM series water film replacement anti-rust oil for several minutes before removing.At this time, a 5 rust-proof oil film is attached to the surface of the spring, which protects the spring from rust.This process greatly reduces t...
    more
  • Testing spring residual stress
    Testing spring residual stress
    2018 . 10 . 10
    271
    Daisy
    Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually obtained by the following two methods:(1) X-ray detection method.X ray detection is a non-destructive testing method. This method can detect residual stress on specific surfaces and sites, but it has ...
    more
  • Type of paint used on spring surfaces
    Type of paint used on spring surfaces
    2018 . 10 . 09
    405
    Daisy
    The paint used for the spring coating is usually of the following types:(1) asphalt paint has good water resistance, moisture resistance and corrosion resistance, especially excellent acid resistance and good alkali resistance.But adhesion, mechanical strength, poor decorative performance.(2) phenolic paint can be divided into two types: primer and topcoat. Phenolic primer has strong adhesion, good rust resistance, but poor mechanical strength and gloss.Phenolic coating film is hard, gloss good, but poor weather resistance, easy to yellow.(3) alkyd paint alkyd paint film is tough, with strong adhesion, good mechanical properties, excellent gloss, good durability and certain oil resistance and insulation properties.Its drawback is that the surface dry fast and long adhesive time, easy wrink...
    more
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
100
Development of special spring and material requirements
Development of special spring and material requirements
2018 - 09 - 28
The special-shaped spring contains spring clip, tension spring and torsion spring, and the generalized special-shaped spring also includes snake spring, corrugated spring, bar spring and other complicated springs.Special-shaped spring is the basic part with wide application range and multifarious variety in automobile, motorcycle, electric appliance and instrument products. Its quality and life directly affect the performance of main engine products.Hyundai has made it a key component.Over 90% of special-shaped springs at home and abroad are made of two kinds of materials: lead quenched carbon...
101
Surface treatment of stainless steel spring
Surface treatment of stainless steel spring
2018 - 10 - 15
There are three ways to use stainless steel spring to remove oil and oxide skin:1. Immerse the stainless steel spring into the plastic container with the metal cleaning agent A diluted with water (the proportion of cleaning agent A and water dilution is 1:1 or 1:2), and the time should be as follows: the spring surface should be free from oil and oxide skin to restore the metal color. The soaking time should not be too long.So stainless steel spring surface has matte effect.2. In the ultrasonic equipment, the proportion of cleaning agent and water is about 1:30. It is advisable to restore the ...
102
Metal spring plays an important role in safety valve
Metal spring plays an important role in safety valve
2018 - 10 - 25
The spring relief valve is mainly composed of spool, seat, stem, spring and adjusting screw.The relief valve mainly USES spring force to press the spool on the seat.When the boiler pressure exceeds the pressure exerted by the spring on the upper part of the spool, the spool and stem are lifted and steam is discharged.When the boiler pressure is lower than the spring pressure acting on the upper part of the spool, the spool falls on the seat and the boiler stops discharging steam.The spool is a cone with a slight protrusion around the edge of the spool.When the steam opens the valve core, the e...
103
Precision metal spring
Precision metal spring
2019 - 12 - 23
Precision metal stamping is a cold-form manufacturing process that converts metal sheets into desired shapes—be it parts, components, or finished products—for a variety of applications. In metal fabrications shops or manufacturing operations, metal sheets, known as blanks, are fed through the tool and die surface of stamping presses to shape and shear the blanks into a finished three-dimensional object. Precision metal stamping services allow for mass production of complex parts in any quantity for nearly all industry.  The automotive industry, in building and construction,...
104
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 04 - 18
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
105
Inspection content and specification for spring parts(part 3)
Inspection content and specification for spring parts(part 3)
2018 - 07 - 28
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
106
Common specifications of spring
Common specifications of spring
2018 - 08 - 09
The number of diameter length is described!(1) the diameter of the spring wire d: is the wire diameter of the spring. (2) the maximum outer diameter of the spring outer diameter D: spring. (3) the inner diameter of the spring D1: the smallest outer diameter of the spring.(4) the middle diameter of the spring D2: the average diameter of the spring. Their formula is: D2 = (D + D) = 2 = D 1 + D = D D.(5) apart from the support ring, the distance between the two adjacent circles of the spring corresponding to the axial distance of the point on the middle diameter is t:, and is expressed ...
107
What is the salt spray test?
What is the salt spray test?
2018 - 08 - 23
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kin...
108
Analysis of deformation prevention measures for heat treatment of metal spring(part 1)
Analysis of deformation prevention measures for heat treatment of metal spring(part 1)
2018 - 09 - 07
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount...
NEW INFORMATION / More
100
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 08 - 06
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
101
Inspection content and specification for spring parts(part 5)
Inspection content and specification for spring parts(part 5)
2018 - 08 - 17
Detection of the characteristics of 7.2 torsion springsWhen measuring torque, the size of the torsional spring axis must be suitable. The inner diameter of the spring should be kept to a certain gap, and the friction force and friction torque caused by the contraction of the inner diameter of the spring should be avoided, and the measurement accuracy should be affected. But the spindle can not be too small, otherwise it will cause the offset between the external torque and the measuring torque center, resulting in the error of the torque measurement. The specific testing program for torsion sp...
102
Steps of hardware spring pressure test
Steps of hardware spring pressure test
2018 - 09 - 03
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compr...
103
Study on factors influencing decarburization of 55SiCr surface of spring steel during heating
Study on factors influencing decarburization of 55SiCr surface of spring steel during heating
2018 - 09 - 14
55SiCr is the high-grade steel used for automobile suspension springs. The suspension springs bear the reciprocating compression motion in the process of automobile driving, and play the role of buffer and shock absorption, which has high requirements on the performance of steel.Decarburization is one of the main problems in the hot processing of spring steel. Decarburization of spring steel surface will seriously damage the fatigue performance of spring, especially when the total decarburization of ferrite occurs on spring steel surface, the fatigue limit of spring can be reduced by 50%.At pr...
104
Spring material selection method
Spring material selection method
2018 - 09 - 26
The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension ...
105
Type of paint used on spring surfaces
Type of paint used on spring surfaces
2018 - 10 - 11
Type of paint used on spring surfacesThe oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite...
106
Surface treatment of springs
Surface treatment of springs
2018 - 10 - 22
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
107
The working characteristic of tension spring
The working characteristic of tension spring
2018 - 12 - 03
Today, the development of science and technology, spring has been a very important hardware accessories in our life, different products use the spring is not the same, the longest used spring can be roughly divided into: tension spring, torsion spring, compression spring, spiral spring, flat spring.The following is a very practical tension spring characteristics of the application:Many different products or hooks are used to ensure that the tension spring tension source, tension spring and compression spring work in the opposite way, tension spring is in the extension or pull out of the revers...
108
Types of springs and their applications
Types of springs and their applications
2018 - 04 - 18
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens. Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms. Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
CONTACT US / More
Consultation
hotline
86-755-28903526
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
Constant Force Spring
Constant Force Spring
2020 . 01 . 13
点击次数: 128
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
More
Compression Springs
Compression Springs
2020 . 01 . 13
点击次数: 136
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
More
Spring wire materials
Spring wire materials
2020 . 01 . 06
点击次数: 80
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
More
Wire forming spring
Wire forming spring
作者： nelson
发布时间： 2018 / 08 / 25
点击次数： 43
Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of elastic element widely used in the mechanical and electronic industry. When the spring is loaded, it can produce large elastic deformation and transform the mechanical work or kinetic energy into deforma...
>>
Each of these types can be further characterized.
Each of these types can be further characterized.
作者： nelson
发布时间： 2018 / 08 / 24
点击次数： 47
We can look at the relationship between the force applied to a spring and its resulting displacement. Again, there are three classes of springs: linear (or constant rate) springs, variable rate springs, and constant force springs.Linear springsLinear springs obey Hooke’s Law (F=k*x), which means that the force needed to extend or compress such a spring by distance x is proportional to the distance, as long as the force doesn’t exceed the elastic limit of the spring. Torsion springs obey an analogous version of Hooke’s Law (F=k*θ, where θ is an angle). In both cases, k is the spring rate, and it stays constant, no matter the spring’s deflection. This is why linear springs are also known as constant rate springs.Variable rate springsOn the other hand, a variable rate spring doesn’t have the ...
>>
Types of springs and their applications
Types of springs and their applications
作者： nelson
发布时间： 2018 / 08 / 24
点击次数： 29
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens.Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms.Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
>>
What is the salt spray test?
What is the salt spray test?
作者： nelson
发布时间： 2018 / 08 / 23
点击次数： 53
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kind of test equipment with a certain volume space - salt spray test machine. In its volume space, the salt fog environment is used to test the salt spray corrosion resistance quality of the product. Com...
>>
Types of Springs and their Applications
Types of Springs and their Applications
作者： nelson
发布时间： 2018 / 08 / 21
点击次数： 51
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sacrificed to satisfy my curiosity. These days, I appreciate the grown-up applications of springs, especially when I drive over potholes on Highway!
>>
History of spring
History of spring
作者： nelson
发布时间： 2018 / 08 / 21
点击次数： 19
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
>>
Inspection content and specification for spring parts(part 7)
Inspection content and specification for spring parts(part 7)
作者： nelson
发布时间： 2018 / 08 / 20
点击次数： 31
8.3.3 test machine should have the following functions: test time or preset function;Dynamic timing or counting function; test amplitude display or control function; automatic stop function.Evaluation of 8.4 spring fatigue test results8.4.1 fatigue life determination: under a given failure condition, the measured spring reachesThe maximum cycle number is the fatigue life of the spring.Verification of 8.4.2 fatigue life: if the number of cycles is tested, if the spring does not failThe validation test proved that the test was passed.8.4.3 reliability verification: according to the given reliability target value, determine the suitability according to the regulations.The number of samples n, under specified test conditions and requirements, according to the required failure mode.Judge. If th...
>>
Inspection content and specification for spring parts(part 6)
Inspection content and specification for spring parts(part 6)
作者： nelson
发布时间： 2018 / 08 / 17
点击次数： 33
8, detection of fatigue property and relaxation rate of spring8.1 spring fatigue performance testing requirements: the spring that bears the variable load is in the internal quality of the enterprise.Quantity control, user inspection, new product certification, certification, industry sampling and process adjustment.In the ring section, the fatigue performance must be tested. The testing method can be tested by fatigue life testThere are two kinds of certificate test or reliability evaluation test, but they are classified and certified for products.Reliability evaluation test must be adopted to assess its reliability index.8.2 spring fatigue test specimen8.2.1 samples shall be manufactured according to the technical documents approved by the procedures, and shall be inspected.8.2.2 samples...
>>
Inspection content and specification for spring parts(part 6)
Inspection content and specification for spring parts(part 6)
作者： nelson
发布时间： 2018 / 08 / 17
点击次数： 26
8, detection of fatigue property and relaxation rate of spring8.1 spring fatigue performance testing requirements: the spring that bears the variable load is in the internal quality of the enterprise.Quantity control, user inspection, new product certification, certification, industry sampling and process adjustment.In the ring section, the fatigue performance must be tested. The testing method can be tested by fatigue life testThere are two kinds of certificate test or reliability evaluation test, but they are classified and certified for products.Reliability evaluation test must be adopted to assess its reliability index.8.2 spring fatigue test specimen8.2.1 samples shall be manufactured according to the technical documents approved by the procedures, and shall be inspected.8.2.2 samples...
>>
共158条页次12/18首页PrePage...  78910111213141516...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Site map
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat