HOT INFORMATION
<
  • The Standing treatment of the spring
    The Standing treatment of the spring
    2018 . 10 . 09
    296
    Daisy
    1. The standing treatment of the compression spring is to compress the spring to the working limit height or to tighten the height several times, usually 3 to 5 times;For the stretching spring, the length of the spring is drawn to the working limit several times;Torsion spring, is the spring in the working direction of the 5522 for the ultimate torsion Angle several times.2. Strong pressure (strong tension and strong torsion) treatment for compression spring is to press the spring into the material layer and the stress exceeds the yield point, resulting in negative residual stress on the surface and positive residual stress on the heart.There are two technological methods: one is the static pressure, which presses the spring to the required height.This method takes up more process equipmen...
    more
  • The fixing (stabilization) of the spring
    The fixing (stabilization) of the spring
    2018 . 10 . 08
    200
    Daisy
    The spring should ideally conform to hooke's law, that is, the relationship between stress and strain in the elastic range is linear.However, since the actual spring steel is a polyphase and polycrystalline material, there must be inconsistencies in composition, structure, elasticity, etc., and the stress and strain deviated from the linear relationship within the elastic range, which is called elastic incompleteness or anelastic.The phenomena such as elastic after effect, elastic lag, stress relaxation and elastic modulus decrease are produced.After tempering, the stabilization process can reduce the elastic imperfection.(1) the fixing process for the compression spring is to compress the spring to the working limit height or to tighten the height several times;For the stretching spri...
    more
  • Oxidation treatment of spring surface
    Oxidation treatment of spring surface
    2018 . 10 . 08
    258
    Daisy
    The oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then made of ferrous ironSodium sulfate interacts with sodium ferrite to form magnetic iron oxide (Pe3O4), or oxide film, with a thickness of about 0.5-1.5 microns.The color of the oxide film depends on the ...
    more
  • How to clean stainless steel spring
    How to clean stainless steel spring
    2018 . 09 . 30
    237
    Daisy
    Washing method according to the surface state:General notice when washing, please pay attention not to scratch the surface to avoid the use of bleaching ingredients and abrasive solution, steel wire ball (brush roller ball), grinding tools, etc. In order to remove the washing liquid, wash the surface with clean water at the end of washing.Surface condition and washing methodDirt and scale removal - wash with soap, mild detergent or warm water.Label and film -- scrubbing with warm water and weak detergent;Binder ingredients - use alcohol or organic solutions;Contamination of fats, oils, lubricants - after being dried with a soft cloth or paper, wash with a neutral detergent or an ammonia solution or a special detergent;Rinse immediately with water, soak in an aqueous solution of ammonia or ...
    more
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
109
Hardness testing method for tempering heat treatment
Hardness testing method for tempering heat treatment
2018 - 09 - 17
Hard inspection method for chemical heat treatment and surface quenching and temperingSurface heat treatment is divided into two categories, one is chemical heat treatment and the other is surface quenching and tempering heat treatment. The hardness test method is as follows:1. Chemical heat treatmentChemical heat treatment is to make the workpiece surface infiltrate one or several chemical elements of the atom, thereby changing the workpiece surface chemical composition, organization and performance.After quenching and tempering, the surface of the workpiece has high hardness, wear resistance...
110
Matters needing attention when choosing custom spring
Matters needing attention when choosing custom spring
2018 - 09 - 27
In order to make it convenient for customers to buy and custom spring, some brief introduction about spring and specification parameters are summarized as follows:The common spring can be classified as: stretching spiral spring, compression spiral spring and torsion spiral spring.Among them, stretch and compression springs are mostly produced in quantity, with complicated specifications but suitable for slight modifications. If a small amount of springs is needed and the characteristics of springs are not critical, they can be purchased easily in the market with a higher unit price.The users o...
111
Spring manufacturing process
Spring manufacturing process
2018 - 10 - 12
There are many ways of making spring, but the main forming part is cold forming and hot forming.In spring in the cold forming process, the spring mainly made by oil material toughening, lead bath quenching tempering spring wire, cold drawn wire, etc., using this kind of material in the manufacturing process of spring generally do not need special heat treatment and only requires the stress relieving, adopted by the spring design work stress and material performance.Spring cold forming process is generally suitable for special-shaped spring with small line diameter or more complicated shape, su...
112
Wire forming spring
Wire forming spring
2018 - 10 - 23
Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of ela...
113
Helical Spring
Helical Spring
2019 - 12 - 16
Helical springsMaterials necessary for every aspect of daily life.  Helical spring is a spring that is subjected to torsional deformation, and its working part is also tightly wound into a helical shape. Its characteristic line is linear, can make compression spring, stretch spring and torsion spring. When the load is large and the radial size is limited, two compression springs with different diameters can be used together to become a combination spring. The total winding number n1 is the sum of the effective winding number n and the supporting winding number n2. Volute coil helical...
114
Team development activity
Team development activity
2018 - 04 - 18
To grow the business, we need to develop management expertise and innovation across the team.Thia is the picture of AFR team development activity in one of the shenzhen beach, From the faceof young team,  we can see the confidence and what they want to achieve!
115
Inspection content and specification for spring parts(part 1)
Inspection content and specification for spring parts(part 1)
2018 - 07 - 27
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in...
116
Manufacturing of Springs
Manufacturing of Springs
2018 - 08 - 08
Springs can also be classified by how they’re made. The first spring that comes to most people’s minds is probably a metal coil spring, also known as a helical spring. However, there are many other types. Even an elastic band can be considered a variable rate spring, since it stores mechanical energy. Coil SpringsLightweight coil springs are made by forming metal wires on an CNC coiling machine. The multi-axis CNC control allows you to create variable pitches and end conditions only limited by your imagination. Springs that come off the coiling machines do not have springy properties. They nee...
117
History of spring
History of spring
2018 - 08 - 21
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
NEW INFORMATION / More
109
Summary of spring parameters and symbols (Part 4)
Summary of spring parameters and symbols (Part 4)
2018 - 08 - 02
M- mass of the object acting on the spring (kg)Ms- spring mass (kg)  N- variable load cycle number  N- spring working circle  Nz- spring support ring number  N1- total number of turns of the spring  P'- Spring single ring stiffness (N/mm)  R- The middle radius of the coil (mm)  R1- inner radius of the coil (mm)  R2- outer radius of the coil (mm)  R- damping coefficient  S- safety factor  T-torque; torque (Nmm)  T'- torsional stiffness (N-mm /(0))T- spring momentTc- cable p...
110
Inspection content and specification for spring parts(part 3)
Inspection content and specification for spring parts(part 3)
2018 - 08 - 16
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
111
Review spring drawings, which items should be examined?
Review spring drawings, which items should be examined?
2018 - 08 - 31
Spring drawings should be audited as follows: geometric parameters audit; physical parameters audit; technical conditions audit.(1) geometric parameters include material size, spring diameter, spring coil number, free height, spring rotation and so on.(2) physical parameters include load, stiffness, theoretical value of deformation, tolerance and so on.(3) Technical conditions include geometric tolerance, heat treatment process requirements, surface treatment, elastic compression treatment and shot peening treatment.
112
Introduction of heat treatment process -- surface quenching
Introduction of heat treatment process -- surface quenching
2018 - 09 - 13
The surface of steel is hardenedIn some parts, the surface layer of the workpiece bears higher stress than the core under the action of alternating loads such as torsion and bending and impact loads.In the case of friction, the surface layer is also constantly worn. Therefore, high strength, high hardness, high wear resistance and high fatigue limit are put forward for some surface layer of parts. Only surface strengthening can meet the above requirements.Because surface quenching has the advantages of small deformation and high productivity, it is widely used in production.According to differ...
113
Characteristics of torsion springs for spring equipment
Characteristics of torsion springs for spring equipment
2018 - 09 - 25
Torsion spring is a mechanical force storage structure, mainly used in ancient crossbow guns and other crossbow.The torsion spring accumulates the force through the twist or rotation of the elastic material with a relatively soft and pliable material, and makes use of it so that the projectile has certain mechanical energy.The modern torsion spring torsion bar is made of excellent elastic steel, and the form is also changed a lot, including the wire on the inner surface of the mechanical watch, the power spring in the toy gyroscope gun, as well as the torsion bar in the tank and car.Small...
114
The finish of the spring surface
The finish of the spring surface
2018 - 10 - 10
In recent years, the surface of the spring has been treated by the spring designers.The finishing (finishing) process is to put the spring directly into a series of finishing machines, such as tilting centrifugal type or spiral vibrating type, eddy current type, and add appropriate grinding materials, grinding agents and water for finishing.General optical finishing is about 20 to 30min. Specific optical finishing time depends on the spring shape and the amount of device.After finishing the finish, remove the spring and rinse it with tap water, then immerse in the SM series water film replacem...
115
The basis of spring material selection
The basis of spring material selection
2018 - 10 - 20
1) the selection basis of environmental factors in the use state of spring products: corrosion resistance, acid corrosion resistance, alkali corrosion resistance, salt corrosion resistance, water corrosion resistance, etc.Weather resistance;Resistance to stress and corrosion, fatigue and corrosion, etc.Wear resistance;Temperature resistance, etc.Radiation resistance, etc.2) selection basis of load characteristics of spring products: dynamic pulse-type cycle load, variable load, impact load, corrosion fatigue load, static load, large load and fatigue load, etc.3) selection basis of mechanical p...
116
The role of spring in driving mechanism of press machine
The role of spring in driving mechanism of press machine
2018 - 11 - 03
In the transmission mechanism of the press, when the clutch and the brake adopt mechanical rigid interlock, as long as the air is set on the clutch.The cylinder, the air pressure ACTS on the piston of the cylinder to make the clutch friction pair fit, and to make the air pressure of the spring brake brake friction pair separate and not brake, so when the air cylinder enters, the brake friction pair should be separated first, and then the clutch friction pair fits to complete the combination.The friction pair separation of the clutch and the friction pair fitting of the brake are respectively a...
117
Pregressive hour
Pregressive hour
2018 - 04 - 18
We do cherish the time together with all of our esteemed customers.  The picture shows the progressive hour withOne of our French customer who focus on the water purification system industry.
CONTACT US / More
Consultation
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
Constant Force Spring
Constant Force Spring
2020 . 01 . 13
点击次数: 139
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
More
Compression Springs
Compression Springs
2020 . 01 . 13
点击次数: 139
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
More
Spring wire materials
Spring wire materials
2020 . 01 . 06
点击次数: 83
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
More
Inspection content and specification for spring parts(part 5)
Inspection content and specification for spring parts(part 5)
作者： nelson
发布时间： 2018 / 08 / 17
点击次数： 40
Detection of the characteristics of 7.2 torsion springsWhen measuring torque, the size of the torsional spring axis must be suitable. The inner diameter of the spring should be kept to a certain gap, and the friction force and friction torque caused by the contraction of the inner diameter of the spring should be avoided, and the measurement accuracy should be affected. But the spindle can not be too small, otherwise it will cause the offset between the external torque and the measuring torque center, resulting in the error of the torque measurement. The specific testing program for torsion spring torque: in addition to the pattern, the spring twists the spring to three times of the torsion angle corresponding to the allowable bending stress; the spring is worn in the test bar, the diamete...
>>
Inspection content and specification for spring parts(part 4)
Inspection content and specification for spring parts(part 4)
作者： nelson
发布时间： 2018 / 08 / 16
点击次数： 46
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30%~ 70% of the deformation amount under the test load.7. the load and stiffness of 1.2 spring load and stiffness can be detected by the spring tension test machine, and the large spring can be tested o...
>>
Inspection content and specification for spring parts(part 3)
Inspection content and specification for spring parts(part 3)
作者： nelson
发布时间： 2018 / 08 / 16
点击次数： 263
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the straightness.Measurement of geometry size of 6.2 stretch springThe dimension of tensile spring is roughly measured: material diameter, free length and spring.The diameter, total number of rings, the r...
>>
nspection content and specification for spring parts(part 2)
nspection content and specification for spring parts(part 2)
作者： nelson
发布时间： 2018 / 08 / 15
点击次数： 45
Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is confirmed that the spring is upright. When the free height or length of the spring is greater than 500mm, the gauge is measured by ordinary steel tape and measured with vernier caliper or height gaug...
>>
Inspection content and specification for spring parts(part 1)
Inspection content and specification for spring parts(part 1)
作者： nelson
发布时间： 2018 / 08 / 15
点击次数： 38
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in full. The inspector will inform the technician of the inspection result.4, Quality conformance testThe scope of application of the 4.1 whole test:4.1.1 Small batches of springs, such as less than 50 ...
>>
The development course of spring material (Part 3)
The development course of spring material (Part 3)
作者： nelson
发布时间： 2018 / 08 / 14
点击次数： 27
(5) the development of spring steel wireAfter more than 100 years of development, the technology of spring steel has experienced lead hardened to oil quenching, and now it develops to induction hardening. Coupled with the continuous innovation and improvement of technology and equipment, the quality of varieties is constantly updated. The newly developed valves have been developed by induction heating and tempering with spring steel wire. It has been proved that the plastic, toughness, relaxation, fracture toughness, delayed fracture resistance, fatigue life and so on are all compared with oil quenched and tempered steel because of the short induction heating time, small quenching microstructure and almost no decarburization layer on the surface of steel wire. The silk has a great improvem...
>>
The development course of spring material (Part 2)
The development course of spring material (Part 2)
作者： nelson
发布时间： 2018 / 08 / 14
点击次数： 38
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by carbon element. In order to improve its special properties, Cu, Ti, Nb, Mn, Cr, Si and N elements can be added.2) the development of nitrogen containing stainless steel. The results of nitrogen generati...
>>
The development course of spring material (Part 1)
The development course of spring material (Part 1)
作者： nelson
发布时间： 2018 / 08 / 13
点击次数： 54
With the development of spring application technology, more requirements for spring materials are put forward. The main reason is to improve the fatigue life and anti relaxation performance under high stress; secondly, according to different uses, it is required for corrosion resistance, non magnetic, electrical conductivity, wear resistance, heat resistance and so on. In addition to the development of new varieties, the spring materials have achieved beneficial results in the aspects of strict control of chemical composition, reducing non-metallic inclusions, improving the surface quality and size accuracy.(1) development of the production process of spring steelIn order to improve the quality of spring steel, the industrial developed countries have generally adopted the refining technolo...
>>
History of spring
History of spring
作者： nelson
发布时间： 2018 / 08 / 13
点击次数： 63
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
>>
共155条页次13/18首页PrePage...  891011121314151617...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Site map
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat