HOT INFORMATION
<
  • 2018 . 10 . 11
    375
    Daisy
    Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat treatment furnace design matches the design of the expert process control system.Eurotherm already has a unique knowledge of aviation and automotive heat treatment specifications.These knowledge and s...
  • 2018 . 10 . 10
    277
    Daisy
    In recent years, the surface of the spring has been treated by the spring designers.The finishing (finishing) process is to put the spring directly into a series of finishing machines, such as tilting centrifugal type or spiral vibrating type, eddy current type, and add appropriate grinding materials, grinding agents and water for finishing.General optical finishing is about 20 to 30min. Specific optical finishing time depends on the spring shape and the amount of device.After finishing the finish, remove the spring and rinse it with tap water, then immerse in the SM series water film replacement anti-rust oil for several minutes before removing.At this time, a 5 rust-proof oil film is attached to the surface of the spring, which protects the spring from rust.This process greatly reduces t...
  • 2018 . 10 . 10
    252
    Daisy
    Spring steel wire will generate residual stress during the process of cold drawing and oil quenching and heat treatment. Moreover, spring wire is formed during the process of manufacturing and shot peening is conducted.High frequency quenching, carburizing, nitrification, etc. are used as surface hardening treatment. As a result of these treatments, residual stress will be generated in the material.The qualitative and quantitative analysis of the residual stress of the material will be an important factor to improve the fatigue properties of the spring.Residual stress of the spring is usually obtained by the following two methods:(1) X-ray detection method.X ray detection is a non-destructive testing method. This method can detect residual stress on specific surfaces and sites, but it has ...
  • 2018 . 10 . 09
    322
    Daisy
    The paint used for the spring coating is usually of the following types:(1) asphalt paint has good water resistance, moisture resistance and corrosion resistance, especially excellent acid resistance and good alkali resistance.But adhesion, mechanical strength, poor decorative performance.(2) phenolic paint can be divided into two types: primer and topcoat. Phenolic primer has strong adhesion, good rust resistance, but poor mechanical strength and gloss.Phenolic coating film is hard, gloss good, but poor weather resistance, easy to yellow.(3) alkyd paint alkyd paint film is tough, with strong adhesion, good mechanical properties, excellent gloss, good durability and certain oil resistance and insulation properties.Its drawback is that the surface dry fast and long adhesive time, easy wrink...
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
100
2018 - 08 - 14
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by ca...
101
2018 - 08 - 25
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn...
102
2018 - 09 - 10
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
103
2018 - 09 - 21
Compression springs are frequently seen and used in daily life. The main principle of compression springs is to provide a hand to the machine and drive it to work.The compression spring has a certain damping capacity, because the product's elastic force is not a fixed value, so every time it is used, there will be a return force, and the force is not a fixed size, which to some extent has the ability to slow down the vibration.As an example, now the car is installed above a compression spring, you will find when driving, its speed is greatly improved, and the movement process there is no s...
104
2018 - 10 - 08
The oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then ma...
105
2018 - 10 - 18
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle ...
106
2018 - 11 - 01
1) make it clear whether to use raw drawn steel wire or lead hardened steel wire;2) propose the requirements of steel wire diameter, strength grade (group) and standard number (select according to table 1.1);3) if there are special requirements such as strength and diameter allowable error, etc. (standard parameters are in parts 2 and 3);4) special packaging and marking requirements (see 1.4);5) carbon steel spring suitable for long-term work under the condition of temperature 121 ℃, highest working temperature should be chosen alloy spring steel.3 special needsShaped cross section: square, re...
107
2020 - 01 - 13
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled in other needed forms such as conical, concave (barrel), convex (hourglass), or various combinations of these. Compression springs are used to resist force and/or store energy,1、CharacteristicsBy far the most widely used type of spring, compression springs are designed to oppose compression and return to its uncompressed length when the applied force is removed. 2、Service LifeIt should be...
108
2018 - 07 - 14
Spring is one of the most commonly used parts in the mechanical and electronic products industry. It can produce very large elastic deformation when it is loaded, and this elastic deformation also transforms mechanical work or kinetic energy into deformation energy, which can unload the change of spring, and disappear and return to the original shape, finally, finally. Transformation of deformation energy into mechanical work or kinetic energy. With the continuous progress of the times, the application of spring is very wide, the automobile, computer, TV, pin, phone, cell phone and so on are u...
NEW INFORMATION / More
100
2018 - 08 - 09
At first, during the experiment, Hooke found that the weight added to the spring was proportional to the elongation of the spring, and he tested his conjectures by many experiments. In 1678, Hooke wrote a spring paper, which introduced the results of experiments on elastic objects, laying the foundation for the development of material mechanics and elastic mechanics.Spring dynamometerIn the early nineteenth Century, under the premise of a lot of experimental work in the former, British scientist Thomas Yang summed up the research results of Hooke and others, pointing out that if the elongation...
101
2018 - 08 - 21
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
102
2018 - 09 - 07
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount...
103
2018 - 09 - 19
Spring machine is now in the production of spring necessary equipment, due to the abundant of spring and the increase of precision is also more and more high to the requirement of spring machine, the spring machine maintenance is particularly important at ordinary times, and the main factors affecting the service life of spring machine has two, one is the operator of whether scientific and standardized operation, another is reasonable in daily maintenance.After using the spring machine for a period of time, the efficiency of the machine will be significantly reduced, affecting the efficiency o...
104
2018 - 09 - 29
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
105
2018 - 10 - 16
The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension ...
106
2018 - 10 - 26
Please avoid the improper way of using (1) more than the use of the maximum compression (300000 back to the conditions, after a close with the use of a long) stress causing the wreck, close to close with the use of a long, can make the spring line department gradually close to that, because of the high spring constant change caused by load curve with high, nearly and produce high stress to make spring break, please do not use more than 300000 times.The use of the spring without prepressure due to the gap caused the spring up and down vibration caused the spring distortion, if there is prepress...
107
2019 - 12 - 23
Precision metal stamping is a cold-form manufacturing process that converts metal sheets into desired shapes—be it parts, components, or finished products—for a variety of applications. In metal fabrications shops or manufacturing operations, metal sheets, known as blanks, are fed through the tool and die surface of stamping presses to shape and shear the blanks into a finished three-dimensional object. Precision metal stamping services allow for mass production of complex parts in any quantity for nearly all industry.  The automotive industry, in building and construction,...
108
2018 - 07 - 28
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
CONTACT US / More
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
2020 . 01 . 13
点击次数: 29
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
2020 . 01 . 13
点击次数: 36
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
2020 . 01 . 06
点击次数: 12
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
作者: nelson
发布时间: 2018 / 08 / 25
点击次数: 29
Wire forming spring is a mechanical part that uses elasticity to work. It is usually made of spring steel. It is used to control the movement of machine parts, to mitigate impact or vibration, to store energy and to measure the magnitude of force. It is widely used in machines and instruments.The spring is just an accumulator. It has the function of storing energy, but it can not release the energy slowly. To realize the function of releasing slowly, it should be realized by "Spring + large transmission ratio mechanism", which is common in the mechanical meter.Spring is a kind of elastic element widely used in the mechanical and electronic industry. When the spring is loaded, it can produce large elastic deformation and transform the mechanical work or kinetic energy into deforma...
作者: nelson
发布时间: 2018 / 08 / 24
点击次数: 27
We can look at the relationship between the force applied to a spring and its resulting displacement. Again, there are three classes of springs: linear (or constant rate) springs, variable rate springs, and constant force springs.Linear springsLinear springs obey Hooke’s Law (F=k*x), which means that the force needed to extend or compress such a spring by distance x is proportional to the distance, as long as the force doesn’t exceed the elastic limit of the spring. Torsion springs obey an analogous version of Hooke’s Law (F=k*θ, where θ is an angle). In both cases, k is the spring rate, and it stays constant, no matter the spring’s deflection. This is why linear springs are also known as constant rate springs.Variable rate springsOn the other hand, a variable rate spring doesn’t have the ...
作者: nelson
发布时间: 2018 / 08 / 24
点击次数: 19
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens.Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms.Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
作者: nelson
发布时间: 2018 / 08 / 23
点击次数: 33
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kind of test equipment with a certain volume space - salt spray test machine. In its volume space, the salt fog environment is used to test the salt spray corrosion resistance quality of the product. Com...
作者: nelson
发布时间: 2018 / 08 / 21
点击次数: 17
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sacrificed to satisfy my curiosity. These days, I appreciate the grown-up applications of springs, especially when I drive over potholes on Highway!
作者: nelson
发布时间: 2018 / 08 / 21
点击次数: 17
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
作者: nelson
发布时间: 2018 / 08 / 20
点击次数: 17
8.3.3 test machine should have the following functions: test time or preset function;Dynamic timing or counting function; test amplitude display or control function; automatic stop function.Evaluation of 8.4 spring fatigue test results8.4.1 fatigue life determination: under a given failure condition, the measured spring reachesThe maximum cycle number is the fatigue life of the spring.Verification of 8.4.2 fatigue life: if the number of cycles is tested, if the spring does not failThe validation test proved that the test was passed.8.4.3 reliability verification: according to the given reliability target value, determine the suitability according to the regulations.The number of samples n, under specified test conditions and requirements, according to the required failure mode.Judge. If th...
作者: nelson
发布时间: 2018 / 08 / 17
点击次数: 14
8, detection of fatigue property and relaxation rate of spring8.1 spring fatigue performance testing requirements: the spring that bears the variable load is in the internal quality of the enterprise.Quantity control, user inspection, new product certification, certification, industry sampling and process adjustment.In the ring section, the fatigue performance must be tested. The testing method can be tested by fatigue life testThere are two kinds of certificate test or reliability evaluation test, but they are classified and certified for products.Reliability evaluation test must be adopted to assess its reliability index.8.2 spring fatigue test specimen8.2.1 samples shall be manufactured according to the technical documents approved by the procedures, and shall be inspected.8.2.2 samples...
作者: nelson
发布时间: 2018 / 08 / 17
点击次数: 10
8, detection of fatigue property and relaxation rate of spring8.1 spring fatigue performance testing requirements: the spring that bears the variable load is in the internal quality of the enterprise.Quantity control, user inspection, new product certification, certification, industry sampling and process adjustment.In the ring section, the fatigue performance must be tested. The testing method can be tested by fatigue life testThere are two kinds of certificate test or reliability evaluation test, but they are classified and certified for products.Reliability evaluation test must be adopted to assess its reliability index.8.2 spring fatigue test specimen8.2.1 samples shall be manufactured according to the technical documents approved by the procedures, and shall be inspected.8.2.2 samples...
155页次12/18首页PrePage...  78910111213141516...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat