HOT INFORMATION
<
  • The Standing treatment of the spring
    The Standing treatment of the spring
    2018 . 10 . 09
    296
    Daisy
    1. The standing treatment of the compression spring is to compress the spring to the working limit height or to tighten the height several times, usually 3 to 5 times;For the stretching spring, the length of the spring is drawn to the working limit several times;Torsion spring, is the spring in the working direction of the 5522 for the ultimate torsion Angle several times.2. Strong pressure (strong tension and strong torsion) treatment for compression spring is to press the spring into the material layer and the stress exceeds the yield point, resulting in negative residual stress on the surface and positive residual stress on the heart.There are two technological methods: one is the static pressure, which presses the spring to the required height.This method takes up more process equipmen...
    more
  • The fixing (stabilization) of the spring
    The fixing (stabilization) of the spring
    2018 . 10 . 08
    200
    Daisy
    The spring should ideally conform to hooke's law, that is, the relationship between stress and strain in the elastic range is linear.However, since the actual spring steel is a polyphase and polycrystalline material, there must be inconsistencies in composition, structure, elasticity, etc., and the stress and strain deviated from the linear relationship within the elastic range, which is called elastic incompleteness or anelastic.The phenomena such as elastic after effect, elastic lag, stress relaxation and elastic modulus decrease are produced.After tempering, the stabilization process can reduce the elastic imperfection.(1) the fixing process for the compression spring is to compress the spring to the working limit height or to tighten the height several times;For the stretching spri...
    more
  • Oxidation treatment of spring surface
    Oxidation treatment of spring surface
    2018 . 10 . 08
    258
    Daisy
    The oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then made of ferrous ironSodium sulfate interacts with sodium ferrite to form magnetic iron oxide (Pe3O4), or oxide film, with a thickness of about 0.5-1.5 microns.The color of the oxide film depends on the ...
    more
  • How to clean stainless steel spring
    How to clean stainless steel spring
    2018 . 09 . 30
    237
    Daisy
    Washing method according to the surface state:General notice when washing, please pay attention not to scratch the surface to avoid the use of bleaching ingredients and abrasive solution, steel wire ball (brush roller ball), grinding tools, etc. In order to remove the washing liquid, wash the surface with clean water at the end of washing.Surface condition and washing methodDirt and scale removal - wash with soap, mild detergent or warm water.Label and film -- scrubbing with warm water and weak detergent;Binder ingredients - use alcohol or organic solutions;Contamination of fats, oils, lubricants - after being dried with a soft cloth or paper, wash with a neutral detergent or an ammonia solution or a special detergent;Rinse immediately with water, soak in an aqueous solution of ammonia or ...
    more
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
109
Penetration testing of springs
Penetration testing of springs
2018 - 09 - 18
Osmosis detection will be the basic principle of the spring of dip coating (penetrant) some penetration ability of the solution, the infiltration of surface defects, and then to remove excess penetrant, appeared in the surface layer of the tu yi agent again, at this point defects remaining in the penetrant sucked out, under the purple pay-off (fluorescence) observation or direct observation, can be found that the existence of defects.Osmotic detection can be used for the detection of ferromagnetic springs as well as non-ferromagnetic materials such as copper alloy and austenitic stainless stee...
110
Development of special spring and material requirements
Development of special spring and material requirements
2018 - 09 - 28
The special-shaped spring contains spring clip, tension spring and torsion spring, and the generalized special-shaped spring also includes snake spring, corrugated spring, bar spring and other complicated springs.Special-shaped spring is the basic part with wide application range and multifarious variety in automobile, motorcycle, electric appliance and instrument products. Its quality and life directly affect the performance of main engine products.Hyundai has made it a key component.Over 90% of special-shaped springs at home and abroad are made of two kinds of materials: lead quenched carbon...
111
Surface treatment of stainless steel spring
Surface treatment of stainless steel spring
2018 - 10 - 15
There are three ways to use stainless steel spring to remove oil and oxide skin:1. Immerse the stainless steel spring into the plastic container with the metal cleaning agent A diluted with water (the proportion of cleaning agent A and water dilution is 1:1 or 1:2), and the time should be as follows: the spring surface should be free from oil and oxide skin to restore the metal color. The soaking time should not be too long.So stainless steel spring surface has matte effect.2. In the ultrasonic equipment, the proportion of cleaning agent and water is about 1:30. It is advisable to restore the ...
112
Metal spring plays an important role in safety valve
Metal spring plays an important role in safety valve
2018 - 10 - 25
The spring relief valve is mainly composed of spool, seat, stem, spring and adjusting screw.The relief valve mainly USES spring force to press the spool on the seat.When the boiler pressure exceeds the pressure exerted by the spring on the upper part of the spool, the spool and stem are lifted and steam is discharged.When the boiler pressure is lower than the spring pressure acting on the upper part of the spool, the spool falls on the seat and the boiler stops discharging steam.The spool is a cone with a slight protrusion around the edge of the spool.When the steam opens the valve core, the e...
113
Precision metal spring
Precision metal spring
2019 - 12 - 23
Precision metal stamping is a cold-form manufacturing process that converts metal sheets into desired shapes—be it parts, components, or finished products—for a variety of applications. In metal fabrications shops or manufacturing operations, metal sheets, known as blanks, are fed through the tool and die surface of stamping presses to shape and shear the blanks into a finished three-dimensional object. Precision metal stamping services allow for mass production of complex parts in any quantity for nearly all industry.  The automotive industry, in building and construction,...
114
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 04 - 18
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
115
Inspection content and specification for spring parts(part 3)
Inspection content and specification for spring parts(part 3)
2018 - 07 - 28
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the ...
116
Common specifications of spring
Common specifications of spring
2018 - 08 - 09
The number of diameter length is described!(1) the diameter of the spring wire d: is the wire diameter of the spring. (2) the maximum outer diameter of the spring outer diameter D: spring. (3) the inner diameter of the spring D1: the smallest outer diameter of the spring.(4) the middle diameter of the spring D2: the average diameter of the spring. Their formula is: D2 = (D + D) = 2 = D 1 + D = D D.(5) apart from the support ring, the distance between the two adjacent circles of the spring corresponding to the axial distance of the point on the middle diameter is t:, and is expressed ...
117
What is the salt spray test?
What is the salt spray test?
2018 - 08 - 23
Salt fog refers to the dispersion system composed of salt micro droplets in the atmosphere. It is one of the three defense series of artificial environment. Many enterprise products need to simulate the destructive nature of the marine surrounding climate to the products. The salt fog test is a simulation of this phenomenon, so the test equipment, salt fog test box, came into being.Salt fog can be divided into two categories, one is natural environmental exposure test, the other is artificial accelerated salt spray environmental test. The artificial simulated salt fog environment test is a kin...
NEW INFORMATION / More
109
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 08 - 06
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
110
Inspection content and specification for spring parts(part 5)
Inspection content and specification for spring parts(part 5)
2018 - 08 - 17
Detection of the characteristics of 7.2 torsion springsWhen measuring torque, the size of the torsional spring axis must be suitable. The inner diameter of the spring should be kept to a certain gap, and the friction force and friction torque caused by the contraction of the inner diameter of the spring should be avoided, and the measurement accuracy should be affected. But the spindle can not be too small, otherwise it will cause the offset between the external torque and the measuring torque center, resulting in the error of the torque measurement. The specific testing program for torsion sp...
111
Steps of hardware spring pressure test
Steps of hardware spring pressure test
2018 - 09 - 03
The spring pressure test of metal springs usually uses electronic digital spring tension and compression testing machine. Electronic digital spring tension and compression testing machine is a special instrument for testing the deformation and load relationship characteristics of tension and compression springs. It is suitable for testing the working load of the tension and compression spring under a certain working length, and also for testing the elastic load of elastic devices such as rubber and spring.The pressure test of metal springs is generally divided into the following steps:1. Compr...
112
Study on factors influencing decarburization of 55SiCr surface of spring steel during heating
Study on factors influencing decarburization of 55SiCr surface of spring steel during heating
2018 - 09 - 14
55SiCr is the high-grade steel used for automobile suspension springs. The suspension springs bear the reciprocating compression motion in the process of automobile driving, and play the role of buffer and shock absorption, which has high requirements on the performance of steel.Decarburization is one of the main problems in the hot processing of spring steel. Decarburization of spring steel surface will seriously damage the fatigue performance of spring, especially when the total decarburization of ferrite occurs on spring steel surface, the fatigue limit of spring can be reduced by 50%.At pr...
113
Spring material selection method
Spring material selection method
2018 - 09 - 26
The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension ...
114
Type of paint used on spring surfaces
Type of paint used on spring surfaces
2018 - 10 - 11
Type of paint used on spring surfacesThe oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite...
115
Surface treatment of springs
Surface treatment of springs
2018 - 10 - 22
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
116
The working characteristic of tension spring
The working characteristic of tension spring
2018 - 12 - 03
Today, the development of science and technology, spring has been a very important hardware accessories in our life, different products use the spring is not the same, the longest used spring can be roughly divided into: tension spring, torsion spring, compression spring, spiral spring, flat spring.The following is a very practical tension spring characteristics of the application:Many different products or hooks are used to ensure that the tension spring tension source, tension spring and compression spring work in the opposite way, tension spring is in the extension or pull out of the revers...
117
Types of springs and their applications
Types of springs and their applications
2018 - 04 - 18
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens. Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms. Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
CONTACT US / More
Consultation
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
Constant Force Spring
Constant Force Spring
2020 . 01 . 13
点击次数: 141
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
More
Compression Springs
Compression Springs
2020 . 01 . 13
点击次数: 140
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
More
Spring wire materials
Spring wire materials
2020 . 01 . 06
点击次数: 85
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
More
Inspection content and specification for spring parts(part 5)
Inspection content and specification for spring parts(part 5)
作者： nelson
发布时间： 2018 / 08 / 17
点击次数： 40
Detection of the characteristics of 7.2 torsion springsWhen measuring torque, the size of the torsional spring axis must be suitable. The inner diameter of the spring should be kept to a certain gap, and the friction force and friction torque caused by the contraction of the inner diameter of the spring should be avoided, and the measurement accuracy should be affected. But the spindle can not be too small, otherwise it will cause the offset between the external torque and the measuring torque center, resulting in the error of the torque measurement. The specific testing program for torsion spring torque: in addition to the pattern, the spring twists the spring to three times of the torsion angle corresponding to the allowable bending stress; the spring is worn in the test bar, the diamete...
>>
Inspection content and specification for spring parts(part 4)
Inspection content and specification for spring parts(part 4)
作者： nelson
发布时间： 2018 / 08 / 16
点击次数： 46
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30%~ 70% of the deformation amount under the test load.7. the load and stiffness of 1.2 spring load and stiffness can be detected by the spring tension test machine, and the large spring can be tested o...
>>
Inspection content and specification for spring parts(part 3)
Inspection content and specification for spring parts(part 3)
作者： nelson
发布时间： 2018 / 08 / 16
点击次数： 263
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the straightness.Measurement of geometry size of 6.2 stretch springThe dimension of tensile spring is roughly measured: material diameter, free length and spring.The diameter, total number of rings, the r...
>>
nspection content and specification for spring parts(part 2)
nspection content and specification for spring parts(part 2)
作者： nelson
发布时间： 2018 / 08 / 15
点击次数： 45
Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is confirmed that the spring is upright. When the free height or length of the spring is greater than 500mm, the gauge is measured by ordinary steel tape and measured with vernier caliper or height gaug...
>>
Inspection content and specification for spring parts(part 1)
Inspection content and specification for spring parts(part 1)
作者： nelson
发布时间： 2018 / 08 / 15
点击次数： 38
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in full. The inspector will inform the technician of the inspection result.4, Quality conformance testThe scope of application of the 4.1 whole test:4.1.1 Small batches of springs, such as less than 50 ...
>>
The development course of spring material (Part 3)
The development course of spring material (Part 3)
作者： nelson
发布时间： 2018 / 08 / 14
点击次数： 27
(5) the development of spring steel wireAfter more than 100 years of development, the technology of spring steel has experienced lead hardened to oil quenching, and now it develops to induction hardening. Coupled with the continuous innovation and improvement of technology and equipment, the quality of varieties is constantly updated. The newly developed valves have been developed by induction heating and tempering with spring steel wire. It has been proved that the plastic, toughness, relaxation, fracture toughness, delayed fracture resistance, fatigue life and so on are all compared with oil quenched and tempered steel because of the short induction heating time, small quenching microstructure and almost no decarburization layer on the surface of steel wire. The silk has a great improvem...
>>
The development course of spring material (Part 2)
The development course of spring material (Part 2)
作者： nelson
发布时间： 2018 / 08 / 14
点击次数： 38
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by carbon element. In order to improve its special properties, Cu, Ti, Nb, Mn, Cr, Si and N elements can be added.2) the development of nitrogen containing stainless steel. The results of nitrogen generati...
>>
The development course of spring material (Part 1)
The development course of spring material (Part 1)
作者： nelson
发布时间： 2018 / 08 / 13
点击次数： 54
With the development of spring application technology, more requirements for spring materials are put forward. The main reason is to improve the fatigue life and anti relaxation performance under high stress; secondly, according to different uses, it is required for corrosion resistance, non magnetic, electrical conductivity, wear resistance, heat resistance and so on. In addition to the development of new varieties, the spring materials have achieved beneficial results in the aspects of strict control of chemical composition, reducing non-metallic inclusions, improving the surface quality and size accuracy.(1) development of the production process of spring steelIn order to improve the quality of spring steel, the industrial developed countries have generally adopted the refining technolo...
>>
History of spring
History of spring
作者： nelson
发布时间： 2018 / 08 / 13
点击次数： 63
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
>>
共155条页次13/18首页PrePage...  891011121314151617...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Site map
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat