HOT INFORMATION
<
  • Wash the stainless steel surface
    Wash the stainless steel surface
    2018 . 10 . 17
    308
    Daisy
    Washing method according to the surface state:General considerationsWhen washing, please pay attention not to scratch the surface to avoid using the bleaching ingredients and the cleaning solution containing abrasive agent, steel ball (brush roller ball), grinding tools, etc. In order to remove the cleaning solution, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and dirt are washed with soap, a mild detergent, or warm waterLabel and film with warm water, weak detergent to scrubThe binder ingredient is alcohol or organic solutionUse a mild cloth or paper to dry and then wash with a neutral detergent or an ammonia solution or a special detergentRinse immediately with water, soak in an aqueous solution of ammonia or neutral carbonated soda, a...
    more
  • Definition and classification of spring steel
    Definition and classification of spring steel
    2018 . 10 . 16
    284
    Daisy
    A, definitions,Spring steel refers to the steel specially used to make spring elastic elements due to its elasticity in the quenching and tempering states.The elasticity of steel depends on its elastic deformation capacity, that is, within the specified range, the elastic deformation capacity makes it bear a certain load, and no permanent deformation occurs after the load is removed.Spring steel shall have excellent comprehensive performance, such as mechanical properties (especially elastic limit, strength limit and yield ratio), anti-elastic and anti-elastic properties (i.e. anti-elastic and anti-loose properties), fatigue properties, quenching properties, physical and chemical properties (heat resistance, low temperature resistance, oxidation resistance, corrosion resistance, etc.).In o...
    more
  • Selection of spring material
    Selection of spring material
    2018 . 10 . 16
    273
    Daisy
    The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension springs, should be preferentially used steel wire, cold-drawn steel wire such as strengthened steel wire, lead bath and oil hardened tempered steel wire, which has higher strength and good surface qua...
    more
  • Surface treatment of stainless steel spring
    Surface treatment of stainless steel spring
    2018 . 10 . 15
    336
    Daisy
    There are three ways to use stainless steel spring to remove oil and oxide skin:1. Immerse the stainless steel spring into the plastic container with the metal cleaning agent A diluted with water (the proportion of cleaning agent A and water dilution is 1:1 or 1:2), and the time should be as follows: the spring surface should be free from oil and oxide skin to restore the metal color. The soaking time should not be too long.So stainless steel spring surface has matte effect.2. In the ultrasonic equipment, the proportion of cleaning agent and water is about 1:30. It is advisable to restore the metal color without oil and oxide skin on the spring surface.The above two methods can be applied to high precision spring.3. After the cleaning agent A is put into the vibration polishing machine wit...
    more
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
82
Analysis of spring corrosion
Analysis of spring corrosion
2018 - 09 - 29
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which i...
83
Selection of spring material
Selection of spring material
2018 - 10 - 16
The selection of spring material shall be determined according to the properties of the spring bearing load, stress state, stress size, working temperature, environmental medium, service life, requirements for conducting and magnetic conductivity, technical performance, material source and price, etc.When determining the shape and size of the material section, the series sizes specified in the national standards and ministerial standards should be selected first, and non-standard series of materials should be avoided as far as possible.Medium and small-sized springs, especially spiral-tension ...
84
Proper use of the spring
Proper use of the spring
2018 - 10 - 26
Please avoid the improper way of using (1) more than the use of the maximum compression (300000 back to the conditions, after a close with the use of a long) stress causing the wreck, close to close with the use of a long, can make the spring line department gradually close to that, because of the high spring constant change caused by load curve with high, nearly and produce high stress to make spring break, please do not use more than 300000 times.The use of the spring without prepressure due to the gap caused the spring up and down vibration caused the spring distortion, if there is prepress...
85
Spring Design
Spring Design
2019 - 12 - 30
Spring design and its fabrication play an important role in manufacturing and industry around the globe. Springs come in all shapes and sizes to meet industry needs and are made from a wide range of metal alloys. Materials used for spring design and wire forming consist of high strength alloys.In general, wire formed into springs is cold rolled or drawn, and a made of medium to high carbon steel with high yield strength that allows for excellent elastic properties.Mechanical PropertiesThe mechanical principles of springs are very basic. They are an elastic component. Potential mechanical ...
86
Types of springs and their applications
Types of springs and their applications
2018 - 04 - 18
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens. Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms. Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
87
Inspection content and specification for spring parts(part 4)
Inspection content and specification for spring parts(part 4)
2018 - 07 - 30
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30...
88
How much do you know about the cleaning of stainless steel springs？
How much do you know about the cleaning of stainless steel springs？
2018 - 08 - 10
Stainless steel spring general precautions when washing, please pay attention to no surface friction to avoid the use of bleaching components and washing liquid containing abrasives, steel ball, grinding tools, etc., in order to remove the washing liquid, washing the end, rinse the surface with clean water.Surface state and washing methodDust and scaling - wash with soap or warm water.Label and film - scrub with warm water and weak detergent.Binder ingredients - use alcohol or organic solution;Fat, oil, lubricating oil contamination - with soft cloth or paper after drying with a neutral deterg...
89
Types of springs and their applications
Types of springs and their applications
2018 - 08 - 24
The most common way to classify springs is by how load is applied to them. You’re probably familiar with the following:Compression spring: designed to operate with a compressive load and found in shock absorbers, spring mattresses, mechanical pencils, and retractable pens.Extension spring: designed to operate with a tensile load. An archetypical example is a Slinky, but these are also found in luggage scales and garage door mechanisms.Torsion spring: designed to operate with torque (twisting force); powers every clothespin and mouse trap.
90
Analysis of deformation prevention measures for heat treatment of metal spring(part 2)
Analysis of deformation prevention measures for heat treatment of metal spring(part 2)
2018 - 09 - 07
In the heat treatment of forgings, the way of placing parts to reduce deformation is to hang them vertically as far as possible, to place them vertically at the bottom of the furnace, to support them horizontally with two points, to place the fulcrum between one-third and one-fourth of the full length, and to place them flat on the heat-resistant steel tooling.In the cooling process of parts, the types, cooling properties and hardenability of quenching medium are related to deformation. The change of cooling performance can be adjusted by changing the viscosity, temperature, liquid pressure, a...
NEW INFORMATION / More
82
Each of these types can be further characterized.
Each of these types can be further characterized.
2018 - 08 - 06
We can look at the relationship between the force applied to a spring and its resulting displacement. Again, there are three classes of springs: linear (or constant rate) springs, variable rate springs, and constant force springs. Linear springs Linear springs obey Hooke’s Law (F=k*x), which means that the force needed to extend or compress such a spring by distance x is proportional to the distance, as long as the force doesn’t exceed the elastic limit of the spring. Torsion springs obey an analogous version of Hooke’s Law (F=k*θ, where θ is an angle). In both cases, k is the spring rate, and...
83
Inspection content and specification for spring parts(part 6)
Inspection content and specification for spring parts(part 6)
2018 - 08 - 17
8, detection of fatigue property and relaxation rate of spring8.1 spring fatigue performance testing requirements: the spring that bears the variable load is in the internal quality of the enterprise.Quantity control, user inspection, new product certification, certification, industry sampling and process adjustment.In the ring section, the fatigue performance must be tested. The testing method can be tested by fatigue life testThere are two kinds of certificate test or reliability evaluation test, but they are classified and certified for products.Reliability evaluation test must be adopted t...
84
What is the cleaning and cleaning of stainless steel springs?
What is the cleaning and cleaning of stainless steel springs?
2018 - 09 - 03
In order to remove the detergent, wash the surface with clean water at the end of washing.Surface condition and washing methodDust and easy to remove dirt - wash with soap, weak lotion or warm water.Label and film: scrub with warm water and weak detergent.Binder composition - using alcohol or organic solution;Fat, oil, lubricating oil contamination - with a soft cloth or paper after drying with a neutral detergent or ammonia solution or special detergent to wash;Bleaching agent and seed acid adherence - immediately rinse with water, soak in ammonia or neutral soda solution, then wash with neut...
85
Knowledge of metal structure and heat treatment
Knowledge of metal structure and heat treatment
2018 - 09 - 17
(1) metal tissue1. Metal: it has good thermal and electrical conductivity with opaque and metallic luster, and its electrical conductivity decreases with the increase of temperature, and it is rich in ductility and malleability.A solid (or crystal) in which the atoms of a metal are regularly arranged.2. Alloy: a substance which is composed of two or more metals or metals and non-metals and has metal properties.3. Phase: components with the same composition, structure and performance in the alloy.Solid solution: an atom (compound) of one (or several) element dissolves into the lattice of anothe...
86
Spring not in place and failure reasons
Spring not in place and failure reasons
2018 - 09 - 27
In the actual work, we often encounter that the spring cannot push the moving object to the set position, that is to say, the length of the spring's computational freedom becomes shorter.The main reason is that there is no initial compression, that is, a spring is made into a spring, which is compressed to its compression height or to its compression height (if necessary) with a greater force, and cannot be restored to its original free length upon release.Its shortened quantity is called "initial compression quantity".After repeating 3-6 times of compression, the length is no lo...
87
Overview of spring surface treatment
Overview of spring surface treatment
2018 - 10 - 12
The spring is often corroded by the surrounding medium in the process of manufacture, storage and use.As the spring works under the influence of the spring force, the spring force will change and lose its function after being corroded.Therefore, preventing the corrosion of the spring can guarantee the stability of the spring and extend its service life.The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic st...
88
Working characteristics of compressure spring
Working characteristics of compressure spring
2018 - 10 - 23
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are calle...
89
THE APPLICATION OF COMPRESSION SPRING
THE APPLICATION OF COMPRESSION SPRING
2019 - 12 - 11
A compression spring comes in many configurations, shapes and sizes. They are conical, hourglass and barrel of varying lengths—and can be used as a shock absorber, vibration damper, a pure energy accumulator, or force generator. Because of their versatility, how efficiently they store energy and the multiple shapes in which they can be manufactured, these types of mechanical springs have a wide selection of applications.In the automotive industry, compression springs are used throughout the vehicle. In the medical applications , compression springs are used as parts in assemblin...
90
Each of these types can be further characterized.
Each of these types can be further characterized.
2018 - 04 - 18
We can look at the relationship between the force applied to a spring and its resulting displacement. Again, there are three classes of springs: linear (or constant rate) springs, variable rate springs, and constant force springs.Linear springsLinear springs obey Hooke’s Law (F=k*x), which means that the force needed to extend or compress such a spring by distance x is proportional to the distance, as long as the force doesn’t exceed the elastic limit of the spring. Torsion springs obey an analogous version of Hooke’s Law (F=k*θ, where θ is an angle). In both cases, k is the spring rate, and i...
CONTACT US / More
Consultation
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
Constant Force Spring
Constant Force Spring
2020 . 01 . 13
点击次数: 139
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
More
Compression Springs
Compression Springs
2020 . 01 . 13
点击次数: 139
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
More
Spring wire materials
Spring wire materials
2020 . 01 . 06
点击次数: 83
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
More
History of spring
History of spring
作者： nelson
发布时间： 2018 / 09 / 11
点击次数： 34
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
>>
Surface treatment of spring equipment prolongs service time
Surface treatment of spring equipment prolongs service time
作者： Daisy
发布时间： 2018 / 09 / 10
点击次数： 41
The corrosion of spring can be divided into chemical corrosion and electrochemical corrosion according to the type of reaction.They are the result of changes in the metal atoms on the surface of the spring or the loss of electrons to an ionic state.If the metal on the surface of the spring simply reacts with the surrounding medium, and the spring causes corrosion, it is called chemical corrosion.For example, the spring is oxidized in the particularly dry atmosphere to form an oxidation film, and the spring is chemically changed with the liquid or impurity in the non-electrolyte liquid, which is a chemical corrosion.If the spring is in contact with the electrolyte solution, the corrosion caused by the action of the micro battery is called electrochemical corrosion.For example, the spring is...
>>
How to prevent cracks at the ends of spring grinding
How to prevent cracks at the ends of spring grinding
作者： nelson
发布时间： 2018 / 09 / 10
点击次数： 57
Spring grinding is easy to produce cracks at the end of the tightness, and directly affect the verticality of the spring, load and free length size, so the general grinding process of spring should be carried out after stress relief tempering. Eliminate the residual stress of steel wire cold drawing to prevent the generation of end gap cracks.The main factors that affect the quality of springs in grinding are as follows:(1) The grinding wheel should be selected reasonably; (2) the control of the bevel angle of the end ring; (3) a certain number of special measuring tools should be equipped to ensure the grinding quality; (4) the grinding wheel should be repaired in time; (5) the correct size of the grinding sleeve should be selected, and the gap between the spring and the sleeve should be ...
>>
Strengthening technology of spring
Strengthening technology of spring
作者： nelson
发布时间： 2018 / 09 / 08
点击次数： 59
(1) heat treatment technology for strengthening springs.1) protective atmosphere heat treatment. In our country, protective atmosphere heat treatment is adopted in spring, oil quenched and tempered steel wire and toughened steel whose wire rod is less than 15mm. Heat treatment in protective atmosphere can remove surface decarbonization and oxidation and improve the surface quality of materials.2) induction heating or protective atmosphere induction heating heat treatment. This process is usually carried out on the wire before forming the coil spring. Some spring factories combine heat treatment of wire materials with spring making to reduce costs. Induction heating treatment has better strengthening effect, rapid induction heating speed, help to refine grain and reduce surface decarbonizat...
>>
Analysis of deformation prevention measures for heat treatment of metal spring(part 2)
Analysis of deformation prevention measures for heat treatment of metal spring(part 2)
作者： nelson
发布时间： 2018 / 09 / 07
点击次数： 32
In the heat treatment of forgings, the way of placing parts to reduce deformation is to hang them vertically as far as possible, to place them vertically at the bottom of the furnace, to support them horizontally with two points, to place the fulcrum between one-third and one-fourth of the full length, and to place them flat on the heat-resistant steel tooling.In the cooling process of parts, the types, cooling properties and hardenability of quenching medium are related to deformation. The change of cooling performance can be adjusted by changing the viscosity, temperature, liquid pressure, additives and stirring of the medium. The higher the viscosity of quenching oil, the higher the temperature, the smaller the elliptical deformation. In static state, the deformation is small.The follow...
>>
Analysis of deformation prevention measures for heat treatment of metal spring(part 1)
Analysis of deformation prevention measures for heat treatment of metal spring(part 1)
作者： nelson
发布时间： 2018 / 09 / 07
点击次数： 28
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount of shrinkage is directly proportional to the supersaturated carbon content. When heated at room temperature of -200, part of austenite is transformed into martensite and expanded. However, the expans...
>>
Production of spring
Production of spring
作者： nelson
发布时间： 2018 / 09 / 06
点击次数： 43
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spring process has to be cut off, a spring connected to several springs is separated into a single spring.Some important springs can add a blank height classification procedure before grinding the face t...
>>
Which industry is the main application of spring?
Which industry is the main application of spring?
作者： nelson
发布时间： 2018 / 09 / 05
点击次数： 44
1, matching springs and springs based on automobiles, motorcycles, diesel engines and gasoline engines. This type of spring has valve spring, suspension spring, damping spring and clutch spring, etc., with a large amount, which accounts for about 50% of the spring production. At the same time, the technical level is also high, it can be said that the technical level of these springs is representative, they are mainly to the high fatigue life and high anti relaxation direction, thus reducing the quality. 2. Large springs and plate springs, which mainly include railway rolling stock, heavy truck and engineering machinery, are mainly formed by hot coil forming, which is an important aspect of the spring manufacturing industry. With the development of high-speed railway and the upgrading ...
>>
Analysis of deformation prevention measures for heat treatment of metal spring
Analysis of deformation prevention measures for heat treatment of metal spring
作者： nelson
发布时间： 2018 / 09 / 04
点击次数： 43
There are two types of heat treatment deformation: one is the size change, the other two is the change of part geometry. Different methods of heat treatment, deformation and deformation prevention of parts size and geometry are also different.The longer the holding time and the higher the temperature are, the more carbon is dissolved into austenite and the larger the expansion of martensite is. The expansion of martensite is the largest, followed by upper bainite, and the volume change of lower bainite and troostite is very small. At low temperature tempering, martensite shrinks and the amount of shrinkage is directly proportional to the supersaturated carbon content. When heated at room temperature of -200, part of austenite is transformed into martensite and expanded. However, the expans...
>>
共155条页次10/18首页PrePage...  567891011121314...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Site map
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat