HOT INFORMATION
<
  • The Standing treatment of the spring
    The Standing treatment of the spring
    2018 . 10 . 09
    296
    Daisy
    1. The standing treatment of the compression spring is to compress the spring to the working limit height or to tighten the height several times, usually 3 to 5 times;For the stretching spring, the length of the spring is drawn to the working limit several times;Torsion spring, is the spring in the working direction of the 5522 for the ultimate torsion Angle several times.2. Strong pressure (strong tension and strong torsion) treatment for compression spring is to press the spring into the material layer and the stress exceeds the yield point, resulting in negative residual stress on the surface and positive residual stress on the heart.There are two technological methods: one is the static pressure, which presses the spring to the required height.This method takes up more process equipmen...
    more
  • The fixing (stabilization) of the spring
    The fixing (stabilization) of the spring
    2018 . 10 . 08
    200
    Daisy
    The spring should ideally conform to hooke's law, that is, the relationship between stress and strain in the elastic range is linear.However, since the actual spring steel is a polyphase and polycrystalline material, there must be inconsistencies in composition, structure, elasticity, etc., and the stress and strain deviated from the linear relationship within the elastic range, which is called elastic incompleteness or anelastic.The phenomena such as elastic after effect, elastic lag, stress relaxation and elastic modulus decrease are produced.After tempering, the stabilization process can reduce the elastic imperfection.(1) the fixing process for the compression spring is to compress the spring to the working limit height or to tighten the height several times;For the stretching spri...
    more
  • Oxidation treatment of spring surface
    Oxidation treatment of spring surface
    2018 . 10 . 08
    258
    Daisy
    The oxidation treatment of the spring (also known as bluish, blackened, cooked black, etc.) is mainly used to prevent the corrosion of the spring, and also to make the spring appearance bright.Oxidation treatment methods include: alkaline oxidation, alkali free oxidation and electrolytic oxidation.Spring oxidation treatment is often alkaline oxidation treatment, in the presence of oxidants (such as sodium nitrite) in caustic sodium solution.As the solution approaches the boiling point, the iron on the surface of the spring dissolves and forms sodium ferrite and sodium ferrite, which is then made of ferrous ironSodium sulfate interacts with sodium ferrite to form magnetic iron oxide (Pe3O4), or oxide film, with a thickness of about 0.5-1.5 microns.The color of the oxide film depends on the ...
    more
  • How to clean stainless steel spring
    How to clean stainless steel spring
    2018 . 09 . 30
    237
    Daisy
    Washing method according to the surface state:General notice when washing, please pay attention not to scratch the surface to avoid the use of bleaching ingredients and abrasive solution, steel wire ball (brush roller ball), grinding tools, etc. In order to remove the washing liquid, wash the surface with clean water at the end of washing.Surface condition and washing methodDirt and scale removal - wash with soap, mild detergent or warm water.Label and film -- scrubbing with warm water and weak detergent;Binder ingredients - use alcohol or organic solutions;Contamination of fats, oils, lubricants - after being dried with a soft cloth or paper, wash with a neutral detergent or an ammonia solution or a special detergent;Rinse immediately with water, soak in an aqueous solution of ammonia or ...
    more
>
INFORMATION
Cooperate with customers to actively develop new products, provide customers with the best r & d team and service quality
Introduction of high precision equipment to improve production technology
News NEWS INFORMATION
HOT INFORMATION / More
109
How to choose spring wire
How to choose spring wire
2018 - 09 - 18
1) make it clear whether to use raw drawn steel wire or lead hardened steel wire;2) propose the requirements of steel wire diameter, strength grade (group) and standard number (select according to table 1.1);3) if there are special requirements such as strength and diameter allowable error, etc. (standard parameters are in parts 2 and 3);4) special packaging and marking requirements (see 1.4);5) carbon steel spring suitable for long-term work under the condition of temperature 121 ℃, highest working temperature should be chosen alloy spring steel.3 special needsShaped cross section: square, re...
110
Automatic spring winding process
Automatic spring winding process
2018 - 09 - 28
The diameter of wire wound by automatic spring machine is 0.2-3mm, and the adjustment process is as follows:1. Calibrate the feeding roller and winch to fit the diameter of steel wire and install the pitch wedge and cutting knife.2. Insert the steel wire into the spring machine and press the pressure plate and feeding roller.3. Adjust the distance of winding xiao zi, control the diameter of spring, and adjust the pitch wedge and xiao zi Angle to control the spring pitch and parallel head.4. Install an appropriate cutter, adjust the feeding CAM according to the spring expansion length, cut off ...
111
Measures to improve spring mass
Measures to improve spring mass
2018 - 10 - 15
(1) deformation heat treatment -- the combination of deformation reinforcement and heat treatment enhancement to further improve the strength and toughness of steel.Heat treatment of deformation has high, medium and low temperature.The high temperature deformation heat treatment is to produce the deformation immediately after the austenitic state at a stable distance, or can be combined with forging or hot rolling, that is, quenching immediately after hot forming.The deformation heat treatment has been applied to automobile plate spring production.(60 si2mn)(2) isothermal quenching of spring -...
112
Production of spring
Production of spring
2018 - 10 - 25
The technological process of helical springs refers to the process of converting spring materials into finished springs, which flow through every process in sequence. Because of the spring material, the spring type and the processing method are different, the technological procedures of the spiral spring are also different. However, their basic technological processes are coil spring heat treatment end processing surface treatment.Next, introduce several typical processes.1. manufacturing compressed spiral spring with cold drawn spring steel wireFor the lathe coil spring, after the winding spr...
113
Medical springs
Medical springs
2019 - 12 - 23
Medical springs are an important component in the manufacturing of devices and equipment used throughout the medical industry. The three main types of springs used in medical devices—compression, torsion, and extension—and each serve a valuable purpose in varying types of equipment, large and small.Springs are devices that store mechanical energy. Though they are relatively simple in design, they are ubiquitous components in all kinds of devices and machines in a wide range of products from medical devices and equipment to consumer goods and heavy industrial equipment. Nearly anythin...
114
Pregressive hour
Pregressive hour
2018 - 04 - 18
We do cherish the time together with all of our esteemed customers.  The picture shows the progressive hour withOne of our French customer who focus on the water purification system industry.
115
Inspection content and specification for spring parts(part 2)
Inspection content and specification for spring parts(part 2)
2018 - 07 - 28
Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is...
116
A brief history of the development of Hooke
A brief history of the development of Hooke's law
2018 - 08 - 09
At first, during the experiment, Hooke found that the weight added to the spring was proportional to the elongation of the spring, and he tested his conjectures by many experiments. In 1678, Hooke wrote a spring paper, which introduced the results of experiments on elastic objects, laying the foundation for the development of material mechanics and elastic mechanics.Spring dynamometerIn the early nineteenth Century, under the premise of a lot of experimental work in the former, British scientist Thomas Yang summed up the research results of Hooke and others, pointing out that if the elongation...
117
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 08 - 21
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
NEW INFORMATION / More
109
The effect of the production process of the spring factory on the product
The effect of the production process of the spring factory on the product
2018 - 08 - 03
Spring is no stranger to everyone. This element is seen everywhere in life. It is also one of the important parts of many industrial machinery equipment. There are many kinds, with different forms, specifications and sizes, and are widely used in the field. Now the spring plant is basically able to produce a variety of different springs. This component is made with special steel. The structure is relatively simple, but it is also required for the production process, so the manufacturer's production equipment and technology will affect the finished product.So if you need to choose a better ...
110
Inspection content and specification for spring parts(part 4)
Inspection content and specification for spring parts(part 4)
2018 - 08 - 16
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30...
111
Causes and preventive measures of quenching cracks
Causes and preventive measures of quenching cracks
2018 - 08 - 31
1. Shape effect is mainly caused by design factors, such as small fillet R, inappropriate location of acupoints, poor cross-sectional transition. 2. Overheating (overheating) is mainly caused by improper temperature control or running temperature, excessive process setting temperature, uneven furnace temperature and other factors. Preventive measures include overhaul, calibration of temperature control system, correction of process temperature, the addition of pad iron between the workpiece and furnace floor, etc.3. Decarbonization is mainly caused by overheating (or overburning), unprote...
112
Method for improving heat treatment performance
Method for improving heat treatment performance
2018 - 09 - 14
Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat ...
113
Working characteristics of pressure spring
Working characteristics of pressure spring
2018 - 09 - 26
For a long time, the shape and performance of the extension spring will change. If the extension spring is always in a certain situation, it may change its quality due to external conditions.Generally, there are the following situations:I. wear of extension spring :Wear can be divided into abrasive, fatigue and corrosion wear fracture.Ii. Brittle fractureThe majority of spring break belongs to brittle fracture.Plastic fracture is possible only when the working temperature is high.In engineering, fatigue fracture, stress corrosion fracture and hydrogen embrittlement fracture are called brittle ...
114
Method for improving heat treatment performance
Method for improving heat treatment performance
2018 - 10 - 11
Manufacturers of heat treatment furnaces are adopting new features designed to improve the overall temperature distribution of their equipment: with improved ambient flow patterns, carefully designed energy and dynamic densities have brought very useful working capabilities.Process consistency is a major issue for aerospace (typically, Nadcap and AMS2750 U.S. army standards) and automotive (TS16949 test equipment) customers, and compatibility with more acceptable standards is building confidence between heat treatment equipment manufacturers and customers.This is especially true when the heat ...
115
Penetration testing of springs
Penetration testing of springs
2018 - 10 - 22
Osmosis detection will be the basic principle of the spring of dip coating (penetrant) some penetration ability of the solution, the infiltration of surface defects, and then to remove excess penetrant, appeared in the surface layer of the tu yi agent again, at this point defects remaining in the penetrant sucked out, under the purple pay-off (fluorescence) observation or direct observation, can be found that the existence of defects.Osmotic detection can be used for the detection of ferromagnetic springs as well as non-ferromagnetic materials such as copper alloy and austenitic stainless stee...
116
Application of valve spring
Application of valve spring
2018 - 11 - 03
Internal combustion engine valve spring, low, medium and high stress valve spring, safety valve spring, pressure reducing valve, electric regulating valve, pneumatic regulating valve, self-support regulating valve, hydraulic control valve, steam trap, gate valve, as per valve, butterfly valve, ball valve, check valve, special valve, hydraulic valve, electromagnetic valve, etc.Relief valve: spring safety valve by using the spring force, spring loaded relief valve is closed and not closed in two kinds of structure, general inflammable, explosive or toxic medium should choose enclosed, steam or i...
117
Types of Springs and their Applications
Types of Springs and their Applications
2018 - 04 - 18
Springs are ubiquitous in all kinds of machines—from consumer products to heavy industrial equipment, take apart anything that involves a mechanism, and chances are, you’ll find a spring inside. Springs are storage devices for mechanical energy—think of them as analogous to batteries! The earliest spring-driven clocks appeared in the 1400s. Fast-forward some 600 years, you still have to charge the Apple Watch everyday, and it’s not nearly as fast as winding a clock…but I digress.My personal fascination with springs began with Slinkies and wind-up toys, and countless mechanical pencils were sac...
CONTACT US / More
Consultation
hotline
86-755-28903525
Room 316,Building 4,Tusincere Science&Technology Park,QingChun Road,LongCheng Street,LongGang District, ShenZhen,China.
Hot News / 热点新闻
Constant Force Spring
Constant Force Spring
2020 . 01 . 13
点击次数: 139
Constant force spring, or “clock” spring, is a roll of prestressed strip which exerts a nearly constant restraining force to resist uncoiling. The force is constant because the change in the radi...
More
Compression Springs
Compression Springs
2020 . 01 . 13
点击次数: 139
A compression spring is an open-coil helical spring that offers resistance to a compressive force applied axially. They are usually coiled at a constant diameter, though they can be coiled i...
More
Spring wire materials
Spring wire materials
2020 . 01 . 06
点击次数: 83
When choosing the right spring, selecting the best spring wire is a critical before manufacturing. Below are some of the most common spring wire materials and their unique characteristics .Stainless S...
More
Inspection content and specification for spring parts(part 5)
Inspection content and specification for spring parts(part 5)
作者： nelson
发布时间： 2018 / 08 / 17
点击次数： 40
Detection of the characteristics of 7.2 torsion springsWhen measuring torque, the size of the torsional spring axis must be suitable. The inner diameter of the spring should be kept to a certain gap, and the friction force and friction torque caused by the contraction of the inner diameter of the spring should be avoided, and the measurement accuracy should be affected. But the spindle can not be too small, otherwise it will cause the offset between the external torque and the measuring torque center, resulting in the error of the torque measurement. The specific testing program for torsion spring torque: in addition to the pattern, the spring twists the spring to three times of the torsion angle corresponding to the allowable bending stress; the spring is worn in the test bar, the diamete...
>>
Inspection content and specification for spring parts(part 4)
Inspection content and specification for spring parts(part 4)
作者： nelson
发布时间： 2018 / 08 / 16
点击次数： 46
7. Detection of the characteristics of cylindrical helical spring7.1 detection of the characteristics of tension and compression springsThe characteristics of the characteristic tensile and compression springs of the 7.1.1 spring should be in accordance with the characteristics of the spring. Under the load of the specified height (or length), the deformation of the spring should be between the 20%~80% of the deformation amount under the test load, and when the I class precision is required, the deformation of the spring should be above 4mm at the specified height load. It should be between 30%~ 70% of the deformation amount under the test load.7. the load and stiffness of 1.2 spring load and stiffness can be detected by the spring tension test machine, and the large spring can be tested o...
>>
Inspection content and specification for spring parts(part 3)
Inspection content and specification for spring parts(part 3)
作者： nelson
发布时间： 2018 / 08 / 16
点击次数： 263
6.1.10 detection of parallelism between ends of springs: the spring is placed vertically on the plate.The difference between the maximum and minimum values of the surface of the end ring is measured by the dial indicator. The difference between the maximum and minimum values is the parallelism deviation between the ends of the spring.6.1.11 spring straightness detection: put the spring level on the plate and roll one.Zhou, determine its maximum bending position and measure the gap between the maximum bending point and the flat plate with a feeler gauge.The measured gap is the deviation of the straightness.Measurement of geometry size of 6.2 stretch springThe dimension of tensile spring is roughly measured: material diameter, free length and spring.The diameter, total number of rings, the r...
>>
nspection content and specification for spring parts(part 2)
nspection content and specification for spring parts(part 2)
作者： nelson
发布时间： 2018 / 08 / 15
点击次数： 45
Detection of geometric size of 6.1 compression springs6.1.1 spring material diameter detection: check the spring material diameter generally with vernier caliper or micrometer. In particular, attention should be paid to the inspection of springs with small winding wires and annealed alloy wires wrapped by automatic spring coiling machines.6.1.2 spring free height or free length detection: the spring is generally placed in horizontal position measurement. It is allowed to be placed in erect position only when the self weight has no obvious effect on the height or length of the spring when it is confirmed that the spring is upright. When the free height or length of the spring is greater than 500mm, the gauge is measured by ordinary steel tape and measured with vernier caliper or height gaug...
>>
Inspection content and specification for spring parts(part 1)
Inspection content and specification for spring parts(part 1)
作者： nelson
发布时间： 2018 / 08 / 15
点击次数： 38
1, Test classificationA) First inspection;B) Quality consistency check.2, A spring group of groupsThe spring shall be inspected according to the batch. Each batch shall consist of the same material specifications, grades, melting furnace numbers and springs made under the same technological conditions.3, First test3.1 The inspection of the production of the spring first piece must be carried out according to the test or inspection items specified in the drawings, and the determination of qualified and unqualified shall be made. 3.2 The first piece of spring must be checked and recorded in full. The inspector will inform the technician of the inspection result.4, Quality conformance testThe scope of application of the 4.1 whole test:4.1.1 Small batches of springs, such as less than 50 ...
>>
The development course of spring material (Part 3)
The development course of spring material (Part 3)
作者： nelson
发布时间： 2018 / 08 / 14
点击次数： 27
(5) the development of spring steel wireAfter more than 100 years of development, the technology of spring steel has experienced lead hardened to oil quenching, and now it develops to induction hardening. Coupled with the continuous innovation and improvement of technology and equipment, the quality of varieties is constantly updated. The newly developed valves have been developed by induction heating and tempering with spring steel wire. It has been proved that the plastic, toughness, relaxation, fracture toughness, delayed fracture resistance, fatigue life and so on are all compared with oil quenched and tempered steel because of the short induction heating time, small quenching microstructure and almost no decarburization layer on the surface of steel wire. The silk has a great improvem...
>>
The development course of spring material (Part 2)
The development course of spring material (Part 2)
作者： nelson
发布时间： 2018 / 08 / 14
点击次数： 38
(4) the development of stainless steelChina is a big country in the production of stainless steel. With the production and development of stainless steel, many varieties have been developed naturally. At present, more than 50 kinds of stainless steel have been developed, which basically meet the needs of domestic production and development, and a brief description of some new varieties developed at present.1) the initial formation of austenitic stainless steel system. Low carbon austenitic stainless steel 0Cr18Ni9 and 00Cr17Ni2Mo2 have been developed to eliminate fatigue corrosion caused by carbon element. In order to improve its special properties, Cu, Ti, Nb, Mn, Cr, Si and N elements can be added.2) the development of nitrogen containing stainless steel. The results of nitrogen generati...
>>
The development course of spring material (Part 1)
The development course of spring material (Part 1)
作者： nelson
发布时间： 2018 / 08 / 13
点击次数： 54
With the development of spring application technology, more requirements for spring materials are put forward. The main reason is to improve the fatigue life and anti relaxation performance under high stress; secondly, according to different uses, it is required for corrosion resistance, non magnetic, electrical conductivity, wear resistance, heat resistance and so on. In addition to the development of new varieties, the spring materials have achieved beneficial results in the aspects of strict control of chemical composition, reducing non-metallic inclusions, improving the surface quality and size accuracy.(1) development of the production process of spring steelIn order to improve the quality of spring steel, the industrial developed countries have generally adopted the refining technolo...
>>
History of spring
History of spring
作者： nelson
发布时间： 2018 / 08 / 13
点击次数： 63
Like most other basic mechanisms, metal springs have existed for a long time in the bronze age. Even for metals, wood is used as a structural member of flexible bow and arrow and military catapult. In the Renaissance, precise clocks made precision springs the first necessity. In Fourteenth Century, we saw the precise clock of revolutionary astronomical navigation developed. The world's exploration and conquest of European colonial powers continue to provide impetus for watchmakers "science and art." The other area of the firearm promotes the development of the spring. At the dawn of the industrial revolution in eighteenth Century, a large, accurate and cheap spring was proposed. Whereas the watchmaker's spring is often made by hand, the spring mass production is made of p...
>>
共155条页次13/18首页PrePage...  891011121314151617...NextPage尾页
Copyright ©2018 AFR PRECISION TECHNOLOGY CO,LTD
Site map
Xiniuyun Providing enterprise cloud services
在线聊天
live chat
-->
客户服务
live chat